Truck Body - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 1U-8233     | Nylon Lifting Sling     | 4     |
B     | 140-7742     | Protective Sleeve     | 4     |
Start By:
- Remove both hoist cylinders. Refer to Disassembly and Assembly, "Hoist Cylinder - Remove".
- Remove two hoses from the counterbalance valve on the tailgate cylinder. Refer to Disassembly and Assembly, "Counterbalance Valve (Tailgate) - Remove".
- Disconnect electrical connections (3) .
Show/hide table
Illustration 1 | g00514991 |
Show/hide table
Illustration 2 | g00514992 |
- Remove bolts (2), the nuts and washers.
- Remove lights (1) .
- Remove bolts (4), the nuts, the bushing and the washers.
- Use four protective sleeves (7) in order to attach four lifting slings (6) to dump body (5). Apply sufficient tension to lifting slings (6) in order to relieve the pressure on pin assemblies (8) .
Show/hide table
Illustration 3 | g00514831 |
Show/hide table
Illustration 4 | g00515030 |
- Use two 3/4 - 10 NC forcing screws (9) in order to remove pin assembly (8) .
Note: If there are shims between the hoist pivot and the pivot bracket, note the location of the shims for assembly.
- Repeat Step 6 for the opposite side of the dump body.
- Remove dump body (5) with lifting slings (6) and a suitable lifting device. The weight of dump body (5) is approximately 3764 kg (8298 lb).
Caterpillar Information System:
725 and 730 Articulated Trucks Machine Systems Hoist Cylinder - Install
725 and 730 Articulated Trucks Machine Systems Hoist Cylinder - Remove
424D, 428D and 438D Backhoe Loaders Transmission Neutral Lock Control
416D, 420D, 424D, 428D, 432D and 442D Backhoe Loaders Transmission (Autoshift) Transmission
725 and 730 Articulated Trucks Machine Systems Counterbalance Valve (Tailgate) - Install
725 and 730 Articulated Trucks Machine Systems Counterbalance Valve (Tailgate) - Remove
725C2 and 730C2 Articulated Truck Machine System Service Brake - Assemble
725 and 730 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Metering Pump (Steering)
725C2 and 730C2 Articulated Truck Machine System Service Brake - Disassemble
2000/11/06 Modifications that Reduce Restrictions in the Air Cleaner are Available {1051, 5056, 5056}
424D, 428D and 438D Backhoe Loaders Alternate Exit
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Tire Inflation - Check
2000/11/27 New Plates Are Used to Secure the Engine Hood on Wheel Harvesters {7251}
735 and 740 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Lowering Control Valve
725 and 730 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems General Information
725 and 730 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Proportional Solenoid (Hoist)
725 and 730 Articulated Trucks Braking System Brake Line Pressure for Front Axle - Test
725 and 730 Articulated Trucks Machine Systems Truck Body - Install
5110B Excavator, 24H Motor Grader, 69D, 769D, 773D, 773E, 776D and 777D Off-Highway Truck/Tractors, 771D, 775D and 775E Quarry Trucks and AD40 Series II, AD45 and AE40 II Underground Articulated Trucks Caterpillar Monitoring System General Information
2001/10/01 A New Film is Now Used to Identify the Float Feature on the Three-Point Hitch {7120}
432D and 442D Backhoe Loaders Transmission Neutral Lock Control
HP750 Processing Head Work Tools
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Machine Systems Bank Valve (Stabilizer) - Disassemble
5110B Excavator, 24H Motor Grader, 69D, 769D, 773D, 773E, 776D and 777D Off-Highway Truck/Tractors, 771D, 775D and 775E Quarry Trucks and AD40 Series II, AD45 and AE40 II Underground Articulated Trucks Caterpillar Monitoring System Diagnostic Code List