Engine Oil Filter Base
Type 1
Show/hide table
 | |
| Illustration 1 | g00509553 |
(1) 4N-8150 Spring
- Length under test force ... 55.25 mm (2.175 inch)
- Test force ... 76 ± 5 N (17.0 ± 1.1 lb)
- Free length after test ... 93.7 mm (3.69 inch)
- Outside diameter ... 20.6 mm (0.81 inch)
- The filter and the cooler bypass valves will open with the following pressure difference. ... 255 ± 20 kPa (37 ± 3 psi)
- Test force ... 76 ± 5 N (17.0 ± 1.1 lb)
(2) Stud
- Apply 9S-3263 Thread Lock Compound on the tapered end of the stud to the following dimension. ... 8.0 mm (0.32 inch)
- Tighten the stud to the following torque. ... 80 ± 14 N·m (60 ± 10 lb ft)
Type 2
Show/hide table
 | |
| Illustration 2 | g00286386 |
(1) Apply 9S-3263 Thread Lock Compound on the tapered end of the stud to the following dimension. ... 10.5 ± 1.5 mm (0.41 ± 0.06 inch)
Tighten the stud to the following torque. ... 68 ± 7 N·m (50 ± 5 lb ft)
Show/hide table
 | |
| Illustration 3 | g00434201 |
View A-A | |
(2) 4N-8150 Spring
- Length under test force ... 55.25 mm (2.175 inch)
- Test force ... 76 ± 5.8 N (17 ± 1.30 lb)
- Free length after test ... 93.7 mm (3.69 inch)
- Outside diameter ... 20.6 mm (0.81 inch)
- The filter and the cooler bypass valves will open with the following pressure difference. ... 255 ± 20 kPa (37 ± 3 psi)
- Test force ... 76 ± 5.8 N (17 ± 1.30 lb)
(3) Tighten the plug to the following torque. ... 100 ± 15 N·m (74 ± 11 lb ft)
Caterpillar Information System:
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head (CABS) Harvester Head System Pressure - Test/Adjust
793B Off-Highway Truck Power Train Pump Drive
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head (CABS) Holding Arm Cylinder - Lubricate
CS-531D, CP-533D and CS-533D Vibratory Compactors Directional Turn Signal Control
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head (CABS) Holding Arm Pivot Bearing - Lubricate
836G Landfill Compactor and 834G Wheel Dozer Power Train Axle Guards (Rear) - Remove and Install
416D Backhoe Loader Hydraulic and Steering System General Information (Hydraulic System)
RM-250C Reclaimer Mixer Sampling Interval and Location of Sampling Valve
3406E and 3456 Engines for Caterpillar Built Machines Camshaft
793B Off-Highway Truck Power Train Transmission Hydraulic Control
793B Off-Highway Truck Power Train Oil Cooler (Transmission)
836G Landfill Compactor and 834G Wheel Dozer Power Train Axle Guards (Front) - Remove and Install
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head (CABS) Harvester Head - Clean/Inspect
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head (CABS) Feed Roller Chain - Inspect/Replace
420D, 428D, 430D, 432D, 438D, 442D and 446B Backhoe Loaders Power Train Electronic Control System MID 081 - CID 0191 - FMI 08
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Access Doors and Covers
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head (CABS) Feed Roller Arm (Cam Curve for the Pivot Pin) - Clean/Lubricate/Adjust
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head (CABS) Feed Roller Arm (Cam Curve for the Pivot Pin) - Check
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Engine Supplement Engine, Torque Converter and Transmission - Separate
3406E and 3456 Engines for Caterpillar Built Machines Engine Oil Pump
836G Landfill Compactor and 834G Wheel Dozer Power Train Fixed Axle (Front) - Remove
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Material Handling Arm Operation
420D, 428D, 430D, 432D, 438D, 442D and 446B Backhoe Loaders Power Train Electronic Control System MID 081 - CID 0268 - FMI 02
3408E and 3412E Engines for Caterpillar Built Machines Ether Injection System - Test