Gear Pump (Implement, Pilot and Braking) - Assemble
Assembly Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 1P-0510 | Driver Group | 1 |
Note: Replace all O-ring seals and gaskets. Apply a light film of SAE 10 oil to all components before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Install retainer ring (35) , seal (34) , backup ring (33) and isolation plate (32) .
Show/hide table
 | |
| Illustration 1 | g00736454 |
- Install plate (31) .
- Install O-ring seal (28) .
Show/hide table
 | |
| Illustration 2 | g00736288 |
- Install gear (29) and gear (30) .
- Install plate (27) .
Show/hide table
 | |
| Illustration 3 | g00736287 |
- Install O-ring seal (22) .
Show/hide table
 | |
| Illustration 4 | g00735555 |
- Install isolation plate (23) , backup ring (24) , seal (25) and retainer ring (26) .
- Install cover (21) .
Show/hide table
 | |
| Illustration 5 | g00735541 |
- Install gear (19) .
- Install eight socket head bolts (20) and the washers. Tighten the bolts to a torque of 100 ± 15 N·m (74 ± 11 lb ft).
- Install body (6) .
Show/hide table
 | |
| Illustration 6 | g00735526 |
- Install four nuts (18) and the washers. Tighten the nuts to a torque of 115 ± 7 N·m (85± 5 lb ft).
Show/hide table
 | |
| Illustration 7 | g00735511 |
- Install plate (16) and hidden seal (17) .
Show/hide table
 | |
| Illustration 8 | g00735473 |
- Install gear (14) and gear (15) .
Show/hide table
 | |
| Illustration 9 | g00735460 |
- Install O-ring seal (11) , seal (12) and plate (13) .
Show/hide table
 | |
| Illustration 10 | g00735449 |
- Use Tooling (A) in order to install lip seal (9) .
Show/hide table
 | |
| Illustration 11 | g00735431 |
- Install O-ring seal (10) .
- Install flange (5) .
Show/hide table
 | |
| Illustration 12 | g00736700 |
- Install eight bolts (8) . Tighten the bolts to a torque of 228 ± 10 N·m (168 ± 7 lb ft).
Show/hide table
 | |
| Illustration 13 | g00735418 |
- Install O-ring seal (4) .
Show/hide table
 | |
| Illustration 14 | g00735404 |
- Install manifold (3) .
Show/hide table
 | |
| Illustration 15 | g00735384 |
- Install four bolts (2) .
- Install plug (1) .
Show/hide table
 | |
| Illustration 16 | g00735378 |
End By: Install the gear pump. Refer to Disassembly and Assembly, "Gear Pump (Implement, Pilot and Braking) - Install".
Caterpillar Information System:
C-15 and C-16 Industrial Engines Air Starting System
2000/09/04 Correction to the Callouts for the Extender Cylinder {5640, 6640, 6641}
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Power Train Oscillating Axle (Rear) - Install
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Power Train Oscillating Axle (Rear) - Remove
631E Series II, 633E Series II and 637E Series II Wheel Tractor-Scrapers Air System and Brakes General Troubleshooting Information
IT28G and IT38G Integrated Toolcarriers and 924G, 924GZ, 928G and 938G Wheel Loaders Power Train Electronic Control System Transmission Control (Shift Lever)
120H, 12H, 135H, 140H, 143H, 14H, 160H, 163H and 16H Motor Graders Caterpillar Monitoring System Charging System
PF-300B and PS-300B Pneumatic Compactors Propel System Torque Converter
IT28G and IT38G Integrated Toolcarriers and 924G, 924GZ, 928G and 938G Wheel Loaders Power Train Electronic Control System Limit Switch (Parking Brake)
Caterpillar Monitoring System Alert Indicator Never Flashes
2001/04/23 Mount Accessories in the Cab with Tapped Holes {7177, 7301, 7325}
Service Life can be Increased with the Installation of LED Lights{1429} Service Life can be Increased with the Installation of LED Lights{1429}
2000/09/25 A New Modification Is Used After the Installation of the Bushing in the Harvester Head and Grapple Damper {5569}
CP-323C and CS-323C Paving Compactors Radiator Core - Clean
2000/08/28 Special Instruction, REHS0894, "Speed Sensor Installation" {4351, 4803, 5058}
2000/08/28 Special Instruction, REHS0895, "Speed Sensor Installation" {4351, 4803, 5058}
TH62, TH63, TH82, TH83 and TH103 Telehandlers Power Train Service and Parking Brake - Install
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head Cold Weather Operation
2000/10/09 New Hinges Are Used on the Compartment Doors of Wheel Harvesters {7273}
C-10 and C-12 Industrial Engines Rear Power Take-Off (RPTO)
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head Harvester Head
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Engine Supplement Governor and Fuel Transfer Pump - Install
Caterpillar Monitoring System Temperature Sender
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Engine Supplement Radiator and Fan - Install