Machine Controls
While you warm up the machine, run the conveyor system. Before you receive the first load of asphalt, check the conveyors and the screed vibrators. The drag conveyors and the auger conveyors must be working properly. The screed vibrators must be working properly.
Use the following procedures in order to check the operation of the conveyor system and the vibratory system.
Conveyor System
Show/hide table
Illustration 1 | g00745135 |
- Apply parking control (3) .
- Set maximum speed potentiometer (1) to half speed.
- Set speed range switch (4) to PAVE.
- Set throttle control (5) to maximum rpm.
- Push propel control (2) completely forward.
- Set conveyor auto/manual controls (6) to AUTO.
Show/hide table
Illustration 2 | g00745138 |
- Set auger control switches (8) to AUTO. The augers should be operating at full rpm.
- If the machine is equipped with the feeder control sensor paddles, rotate the paddles outward. This ensures that the augers will slow at some point in the range. If the machine is equipped with sonic sensors, position the sensors in order to stop the augers at the desired mix height. When you position the sonic sensors, set mix height dials (9) to one-half. To adjust the head of material, use the mix height dial.
Show/hide table
Illustration 3 | g00745152 |
Vibratory System
Show/hide table
Illustration 4 | g00800556 |
- Turn vibratory switch (7) on the operator's console to the ON position.
- Turn vibratory switch (10) in the right screed control box to the ON position. The vibrators should be operating.
Show/hide table
Illustration 5 | g00745157 |
- The speed of the vibrators can be adjusted with adjusting knob (11) on the vibratory manifold.
Show/hide table
Illustration 6 | g00745160 |
- Return propel lever (2) to NEUTRAL.
Show/hide table
Illustration 7 | g00800573 |
Caterpillar Information System:
3512 and 3516 EUI Engines and 784B, 785B, 789B and 793B Off-Highway Truck/Tractors Fan Drive
CB-334D and CB-335D Vibratory Compactors Hydraulic System Oil Level - Check
HF181, HF201 and HF221 Felling Heads for Track Feller Bunchers Bearing for Output Shaft - Lubricate
IT28G and IT38G Integrated Toolcarriers and 924G, 924GZ, 928G and 938G Wheel Loaders Power Train Electronic Control System Electronic Control Module
HF181, HF201 and HF221 Felling Heads Output Shaft Spline - Lubricate
AP-1050B and BG-245C Asphalt Pavers Tow Point Cylinders
CB-334D and CB-335D Vibratory Compactors Neutral Start Switch - Test
TH62, TH63, TH82 and TH83 Telehandlers Steering and Hydraulic System Control Valve (Compensating Cylinder)
CB-334D and CB-335D Vibratory Compactors Throttle Control - Lubricate
CB-334D and CB-335D Vibratory Compactors Tire Scraper - Inspect/Adjust/Replace
2000/11/13 New Troubleshooting Procedures for Interlock Electronic Control System {7630}
CB-334D and CB-335D Vibratory Compactors Belts - Inspect/Adjust/Replace
TH62, TH63, TH82 and TH83 Telehandlers Steering and Hydraulic System Boom Cylinder (Raise/Lower)
CB-334D and CB-335D Vibratory Compactors Hydraulic System Oil Sample - Obtain
3408B and 3408C Industrial and Marine Engines Exhaust Manifold - Water Cooled
CB-334D and CB-335D Vibratory Compactors Hydraulic Tank Strainer - Clean
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Fan Drive
CB-334D and CB-335D Vibratory Compactors Indicators and Gauges - Test
TH103 Telehandler Steering and Hydraulic System Control Valve (Compensating Cylinder)
AP-1050B and BG-245C Asphalt Pavers Screed Adjustment
TH62, TH63, TH82 and TH83 Telehandlers Steering and Hydraulic System Boom Cylinder (Raise/Lower)
CB-334D and CB-335D Vibratory Compactors Rollover Protective Structure (ROPS) - Inspect
CB-334D and CB-335D Vibratory Compactors Speed and Direction Control - Lubricate
CB-334D and CB-335D Vibratory Compactors Steering Cylinder Ends - Lubricate