Fuel Filter Base - Install
Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| B | 9S-3263 | Thread Lock Compound | 1 |
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Apply Tooling (B) to the threads of the mounting stud for the fuel filter. Apply the compound to the tapered end of the stud no more than 7.6 mm (0.30 inch) from the end.
- Install the stud and tighten to a torque of 70 ± 15 N·m (50 ± 11 lb ft).
- Inspect the condition of the O-ring seals. Replace the seals, if necessary.
- Install the O-ring seals on fuel filter base (5) .
Show/hide table
 | |
| Illustration 1 | g01019035 |
Typical example | |
- Install fuel filter base (5) on the fuel manifold with bolts (4) .
- Connect hose assembly (3) .
- Install fuel temperature sensor (2). Connect the sensor harness assembly to fuel temperature sensor (2) .
- Install new fuel filter (6). Follow the instructions on the fuel filter.
- Install pressure plug (1) .
Show/hide table
 | |
| Illustration 2 | g01019031 |
Caterpillar Information System:
3176C and 3196 Engines For Caterpillar Built Machines Fuel Filter Base - Remove
10-20B Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Extender - Adjust
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks Intermittent Low Power or Power Cutout
CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Gear Pump
Alternator - Delco 21SI Alternator - Assemble
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks Intermittent Engine Shutdown
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Body and Canopy - Install
2000/07/31 A Special Instruction for the Ultrasonic Testing of Brake Bands is now Available {4110}
2000/05/15 A Special Instruction for the Relocation of the Ladder and the Platform is now Available {7254}
12H Motor Grader Rollover Protective Structure (ROPS) - Inspect
3126B Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
3176C and 3196 Engines for Caterpillar Built Machines Fuel Dilution of Engine Oil
725 and 730 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Suspension System
TH62, TH63, TH82, TH83 and TH103 Telehandlers Machine Systems Counterweight - Remove and Install
2000/05/22 A New Plate for the Fuse Panel Deflects Rain and Water {7323, 7451}
2000/05/15 A Special Instruction for the Installation of the 187-6171 Open ROPS Heater Gp is now Available {7304}
3408E and 3412E Engines for Caterpillar Built Machines CID 0091 FMI 00 Throttle Switch not released
143H and 163H Motor Graders Seat - Inspect
3408E and 3412E Engines for Caterpillar Built Machines CID 0091 FMI 02 Incorrect Throttle Switch inputs
3408E and 3412E Engines for Caterpillar Built Machines CID 0264 FMI 08 Decel Throttle Position signal abnormal
3126B Engine for Lexion 450, Lexion 460, and Lexion 460 R Combines No Diagnostic Codes Detected
2000/05/22 Correction to Operation and Maintenance Manual, SEBU6652 and to Operation and Maintenance Manual, SEBU7356 for the Transmission Oil {7560, 7581}
C15 and C18 Engines for Caterpillar Built Machines CID 0266 FMI 02 Incorrect Crank-without-inject inputs
2000/06/19 5T-5925 Guide Assembly No Longer Used {7258}