Body and Canopy - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 8S-9906 | 棘轮拉拔器 | 1 |
B | FT-0964 | 销 | 1 |
Show/hide table
吊装或垫塞不当可能会造成人员伤亡。 当使用起重机或千斤顶顶升任何零件或部件时,与之保持距离。 确保起重机或千斤顶具备正确的部件吊装能力。 在沉重部件下面进行任何工作之前先安装垫块或台架。 图上显示的是部件的近似重量。 清洁要安装零件的所有表面。 |
注: 先将机器停在光滑、水平的表面上,然后再进行任何操作。
- 检查机架组件中的套筒轴承有无磨损或损坏。 如有必要,请更换套筒轴承。
Show/hide table
图 1 g00706928 - 将适当的吊索放置到泵体组件 (1) 上。 将适当的起吊设备固定在举倾机构上。 将泵体组件 (1) 放置到机架组件上,如图所示。 泵体组件的重量约为
22080 kg (48685 lb) 。Show/hide table图 2 g00706972 注: 止推垫圈 (18) 位于机架组件 (16) 外侧和泵体组件 (1) 之间,如图所示。 仅当六毫米止推垫圈无法进入两处时,才可使用四毫米止推垫圈。
- 经由泵体组件 (1)、止推垫圈 (18) 和机架组件 (16) 插入销组件 (17)。
Show/hide table
图 3 g00706907 - 将板 (15) 放置在泵体组件 (1) 上。 安装固定板 (15) 的两个螺栓 (14) 和硬垫圈。
- 对其余的销组件重复步骤 3 至步骤 4。
Show/hide table
图 4 g00706886 - 将支架 (11) 和磁铁 (12) 作为一个组件放置在泵体组件上。 安装将支架 (11) 固定到泵体组件上的两个螺栓 (13) 和硬垫圈。
- 将磁铁 (12) 与电子控制对准。 请参阅液压系统,系统操作、测试和调整, "电子控制(泵体向下或向上开关)- 调整"。
Show/hide table
图 5 g00706879 Show/hide table图 6 g00707036 典型实例 - 将适当的吊索绕举升油缸 (7) 的缸盖端安置,如图所示。 将工具 (A) 固定到适当的吊索上。 将工具 (A) 固定到机架组件上。 使用工具 (A) 提升举升油缸 (7) 的缸盖端到适当位置,如图所示。 安装工具 (B) 使举升油缸中的轴承对准泵体组件 (1) 中的孔。
注: 工具 (B) 的直径比用于将举升油缸 (7) 缸盖端固定到泵体组件的销的直径小。
Show/hide table图 7 g00706827 典型实例 - 将一个隔套(未显示)放置在泵体组件 (1) 内的举升油缸 (7) 中的轴承两侧。 穿过泵体组件 (1) 将销 (10) 安装到举升油缸缸盖端内,如图所示。 这将从轴承上拆下工具 (B)。 确保将隔套正确放置在销 (10) 上。
注: 插入销 (10),槽口向上。
- 将板 (9) 放置在销 (10) 上。 安装将板 (9) 固定到泵体组件 (1) 上的两个螺栓 (8) 和硬垫圈。
- 对其余的举升油缸重复步骤 8 至步骤 10。
Show/hide table
图 8 g00706815 典型实例 - 需要两人放置岩石推出器组件 (4),如图所示。 岩石推出器组件的重量为
39 kg (86 lb) 。 安装将岩石推出器组件 (4) 固定到安装支架 (6) 上的销 (5)、八个垫圈 (2) 和开口销 (3)。 - 对其余的岩石推出器组件重复步骤 12。
结束:
- 取走车轮楔子。 请参阅拆解和组装, "车轮楔子(前和后)- 拆卸和安装"。
Caterpillar Information System:
2000/07/31 A Special Instruction for the Ultrasonic Testing of Brake Bands is now Available {4110}
2000/05/15 A Special Instruction for the Relocation of the Ladder and the Platform is now Available {7254}
12H Motor Grader Rollover Protective Structure (ROPS) - Inspect
3126B Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
3176C and 3196 Engines for Caterpillar Built Machines Fuel Dilution of Engine Oil
776D Wheeled Tractor and 777D and 777D HAA Off-Highway Trucks Power Train Spindle (Rear) - Install
3126B Engines for Caterpillar Built Machines Housing (Front) - Install
2000/06/26 Reinforcement and Repair Procedures for the Circle Assembly {6154, 6154, 6157, 6157}
3126B Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
2000/06/05 Design Improvements for the Drum Assembly {3278, 6060, 6605, 6606, 7253}
10-20B Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Deflector - Adjust
3126B Engines for Caterpillar Built Machines Flywheel - Remove and Install
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks Intermittent Engine Shutdown
Alternator - Delco 21SI Alternator - Assemble
CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Gear Pump
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks Intermittent Low Power or Power Cutout
10-20B Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Extender - Adjust
3176C and 3196 Engines For Caterpillar Built Machines Fuel Filter Base - Remove
3176C and 3196 Engines For Caterpillar Built Machines Fuel Filter Base - Install
725 and 730 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Suspension System
TH62, TH63, TH82, TH83 and TH103 Telehandlers Machine Systems Counterweight - Remove and Install
2000/05/22 A New Plate for the Fuse Panel Deflects Rain and Water {7323, 7451}
2000/05/15 A Special Instruction for the Installation of the 187-6171 Open ROPS Heater Gp is now Available {7304}
3408E and 3412E Engines for Caterpillar Built Machines CID 0091 FMI 00 Throttle Switch not released