Fuel Filter Base - Remove
Removal Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 185-3630 | Strap Wrench Assembly | 1 |
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Remove pressure plug (1) and drain fuel into a suitable container for storage or disposal.
Show/hide table
 | |
| Illustration 1 | g01019031 |
- Use Tooling (A) to remove fuel filter (6) .
Show/hide table
 | |
| Illustration 2 | g01019035 |
Typical example | |
- Disconnect the sensor harness assembly from fuel temperature sensor (2) .
- Remove fuel temperature sensor (2) .
- Disconnect hose assembly (3). Plug all openings immediately.
- Remove bolts (4) .
- Remove fuel filter base (5) and the O-ring seals.
- Remove the mounting stud for the fuel filter from the fuel filter base, if necessary.
Caterpillar Information System:
10-20B Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Extender - Adjust
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks Intermittent Low Power or Power Cutout
CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Gear Pump
Alternator - Delco 21SI Alternator - Assemble
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks Intermittent Engine Shutdown
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Body and Canopy - Install
2000/07/31 A Special Instruction for the Ultrasonic Testing of Brake Bands is now Available {4110}
2000/05/15 A Special Instruction for the Relocation of the Ladder and the Platform is now Available {7254}
12H Motor Grader Rollover Protective Structure (ROPS) - Inspect
3126B Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
3176C and 3196 Engines for Caterpillar Built Machines Fuel Dilution of Engine Oil
776D Wheeled Tractor and 777D and 777D HAA Off-Highway Trucks Power Train Spindle (Rear) - Install
3176C and 3196 Engines For Caterpillar Built Machines Fuel Filter Base - Install
725 and 730 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Suspension System
TH62, TH63, TH82, TH83 and TH103 Telehandlers Machine Systems Counterweight - Remove and Install
2000/05/22 A New Plate for the Fuse Panel Deflects Rain and Water {7323, 7451}
2000/05/15 A Special Instruction for the Installation of the 187-6171 Open ROPS Heater Gp is now Available {7304}
3408E and 3412E Engines for Caterpillar Built Machines CID 0091 FMI 00 Throttle Switch not released
143H and 163H Motor Graders Seat - Inspect
3408E and 3412E Engines for Caterpillar Built Machines CID 0091 FMI 02 Incorrect Throttle Switch inputs
3408E and 3412E Engines for Caterpillar Built Machines CID 0264 FMI 08 Decel Throttle Position signal abnormal
3126B Engine for Lexion 450, Lexion 460, and Lexion 460 R Combines No Diagnostic Codes Detected
2000/05/22 Correction to Operation and Maintenance Manual, SEBU6652 and to Operation and Maintenance Manual, SEBU7356 for the Transmission Oil {7560, 7581}
C15 and C18 Engines for Caterpillar Built Machines CID 0266 FMI 02 Incorrect Crank-without-inject inputs