Final Drive Bearings - Adjust
Show/hide table
Illustration 1 | g00699831 |
Final Drive |
Bearing Adjustment Procedure
Show/hide table
Necessary Tools     | ||
---|---|---|
Part Number     | Description     | Qty     |
5P-4202     | Spanner Wrench     | 1     |
Note: The following procedure must be used in order to put the correct amount of preload on the final drive bearings.
- Adjust the axle shaft bearing.
- Tighten 7I-5000 Ring (2) in order to preload the final drive bearings. Rotate the shaft and rap the sprockets while the 7I-5000 Ring is being tightened.
- The final rolling torque should be from 15 to 45 N·m (130 to 400 lb in).
Procedure for End Play Adjustment
- Measure the thickness of housing (4) at the four 12 mm puller holes in the bolt pattern. Average the thickness.
Note: Do not install seal (3) at this time.
- Remove all the existing shims. Bolt housing (4) in place with four evenly spaced bolts. Tighten the four bolts to 900 ± 100 N·m (664 ± 74 lb ft) in order to seat the parts. Loosen the four bolts. Tighten the four bolts to a torque of 20 N·m (15 lb ft).
- Measure the depth to the differential housing through the four puller holes. Average the four numbers.
Note: The housing may have only two puller holes. In order to obtain the four measurements that are required, remount the housing 90° from the original position. Measure the depth of the housing again.
- Subtract the measurement in Step 1 from the measurement in Step 3 and add 0.060 mm (0.0024 inch).
- Remove housing (4) from the differential. Add the amount of shims that are necessary to equal the thickness in Step 4 within 0.020 mm (0.0008 inch).
Note: Install seal (3) at this time.
- Tighten 38 bolts (1) to a torque of 900 ± 100 N·m (664 ± 74 lb ft).
Caterpillar Information System:
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System MID 082 - CID 0355 - FMI 06
CS-531D, CP-533D and CS-533D Vibratory Compactors Ether Starting Aid
2000/06/05 Improvements Have Been Made to the Drum Drive Gear Reducers {5655, 5656}
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Brake Valve (Parking and Secondary) - Remove
797 Off-Highway Truck Power Train Gear Pump (Torque Converter Charging and Transmission Lubrication) - Assemble
2000/05/08 A Special Instruction, REHS0540-01, "Repair Cracks in the Rear Track Roller Frame" Is Available {4151}
140H and 160H Motor Graders Blade Lift Cylinder Socket - Lubricate
D400E Series II Ejector Truck Suspension - Lower
TH62, TH63, TH82, TH83 and TH103 Telehandlers Longitudinal Stability Indicator System Switch (Boom) - Test
797 Off-Highway Truck Power Train Gear Pump (Transmission Charging and Scavenge) - Assemble
797 Off-Highway Truck Power Train Gear Pump (Transmission Charging and Scavenge) - Disassemble
834G Wheel Dozer and 836G Landfill Compactor Electrohydraulic System Calibration
12H Motor Grader Centershift Lock Bar - Clean/Lubricate
953C, 963C and 973C Track-Type Loaders Transmission Electronic Control System Electronic Control Module (ECM) - Flash Program
24H Motor Grader Power Train Differential and Bevel Gear - Adjust
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Brake Valve (Parking and Secondary) - Install
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System MID 082 - CID 0356 - FMI 03
24H Motor Grader Power Train Transfer Gear (Output) - Adjust
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Steering Cylinder - Remove and Install
24H Motor Grader Power Train Transfer Gear (Input) - Adjust
CS-531D, CP-533D and CS-533D Vibratory Compactors Ether Starting Aid Cylinder - Replace
3508B Engine for 854G Wheel Dozers and 992G Wheel Loaders MID 036 - CID 0799 - FMI 12 Need Service tool update
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System MID 082 - CID 0356 - FMI 05
325D and 329D Excavators Hydraulic System Pilot Valve (Travel)