Drive Shaft (Front) - Remove and Install
Removal Procedure
Start By:
- Remove the carrier bearing for the drive shaft. Refer to Disassembly and Assembly, "Carrier Bearing (Driveshaft) - Remove and Install" for the machine that is being serviced.
- Support front drive shaft (1) with a suitable lifting device.
Show/hide table
Illustration 1 | g00516471 |
- Remove bolts (2) that hold front drive shaft (1) to the yoke on the front axle housing.
- Use two people to carefully remove front drive shaft (1). The weight of front drive shaft (1) is approximately 36 kg (80 lb).
Installation Procedure
Show/hide table
NOTICE |
---|
When the front drive shaft is installed, it must be installed in phase with the front axle assembly yoke. The front drive shaft must be installed in phase with the center and rear drive shafts. Serious component damage could occur. Be certain that all the joint groups, all the yokes, and all the lubricating fittings are aligned. |
- Use two people to carefully install front drive shaft (1). The weight of front drive shaft (1) is approximately 36 kg (80 lb).
Show/hide table
Illustration 2 | g00516471 |
- Install bolts (2) that hold front drive shaft (1) to the yoke on the front axle housing. Tighten bolts (2) to a torque of 150 ± 15 N·m (110 ± 11 lb ft). Refer to Illustration 3 for the correct tightening sequence.
Show/hide table
Illustration 3 | g00783350 |
- Remove the suitable lifting device from front drive shaft (1) .
- Lubricate the front drive shaft. For the correct procedure, refer to Operation and Maintenance Manual for the machine that is being serviced.
End By: Install the carrier bearing for the drive shaft. Refer to Disassembly and Assembly, "Carrier Bearing (Driveshaft) - Remove and Install" for the machine that is being serviced.
Caterpillar Information System:
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Hydraulic Oil Contamination - Test
583R Pipelayer Power Train Drawbar
773D Off-Highway Truck and 775D Quarry Truck Air System and Brakes Solenoid Valve (Secondary Steering)
527 Track-Type Skidder Power Train Selector and Pressure Control Valve
CB-534C and CB-634C Vibratory Compactors Steering System Hydraulic Pump
D250E Series II and D300E Series II Articulated Trucks Machine Systems Service Brake - Assemble
784C and 785C Off-Highway Trucks Machine Systems Body and Canopy - Install
3406C Engines for Caterpillar Built Machines Flywheel Housing
980G Wheel Loader Power Train Carrier Bearing (Drive Shaft) - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Pan - Remove and Install
527 Track-Type Skidder Power Train Priority Valve
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Power Train Track - Tension/Detension
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Machine Preparation for Troubleshooting
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Pump Flow - Test
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Visual Inspection
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Operational Checks
3176C and 3196 Engines For Caterpillar Built Machines Cylinder Liner - Install
AP-1000B and BG-260C Asphalt Pavers Engine Starting
527 Track-Type Skidder Power Train Undercarriage
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Steering Cylinder - Install
69D and 769D Off-Highway Truck and 771D Quarry Truck Air System and Brakes Oil Filter (Parking Brake Release)
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Machine Preparation for Troubleshooting
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Steering System Troubleshooting
980G Wheel Loader Power Train Drive Shaft (Center) - Remove and Install