Gear Pump (Rear Axle Lube) - Assemble
- Install lip seal (7) and spacer (5).
Note: Lip seal (7) is made of Viton. Do not substitute any other seal.
- Install bearing (3) and spacer (4) on the shaft.
Note: Bearing (3) is pressed on the shaft.
- Use Tool (A) to install retaining ring (6).
- Install shaft assembly (12).
- Install retaining ring (2).
- Install thrust plate (9).
- Install O-ring seal (8).
- Install housing assembly (16).
- Install idler gear (11) and drive gear (10).
Note: Drive gear (10) has an internal spline which accepts the external spline on shaft (12).
- Install thrust plate (9) and O-ring seal (8).
- Install housing assembly (17).
Note: Two bearings (13) and ring seal (14) are not serviced. Ring seal (14) is only installed in the bore of the drive gear.
- Install four washers and four bolts (18).
Note: During the installation of bolts (18), tighten the bolts to a torque of
160 ± 30 N·m (118.01 ± 22.13 lb ft) .Show/hide tableIllustration 2 g00510889 - Install key (1).
Show/hide table
Illustration 1 | g00510893 |
End By:
- Install the gear pump (rear axle lube). Refer to Disassembly and Assembly, "Gear Pump (Rear Axle Lube) - Remove and Install".
Caterpillar Information System:
793C Off-Highway Truck/Tractor Power Train Gear Pump (Rear Axle Lube) - Disassemble
784C, 785C and 785C HAA Off-Highway Truck Air System and Brakes Parking and Secondary Brake Release System Leakage - Check
527 Track-Type Skidder Traveling with a Load
C27 and C32 Engines for Caterpillar Built Machines Engine Oil Pump
527 Track-Type Skidder Attaching Winch Cable to Logs
CB-434C, CB-534C and CB-634C Vibratory Compactors Water Spray System Water Tank (Rear)
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement Hydraulic Application Guidelines
3306C Engines for Caterpillar Built Machines Valve Rocker Arms and Lifters
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Steering and Brake Manifold Valve - Install
527 Track-Type Skidder Power Train Front Frame
527 Track-Type Skidder Power Train Pivot Shaft
CB-434C, CB-534C and CB-634C Vibratory Compactors Water Spray System Water Tank (Front)
793C Off-Highway Truck/Tractor Power Train Torque Converter - Remove
554 Forwarder and 574 Forwarder Engine Start Switch
793C Off-Highway Truck/Tractor Power Train Torque Converter - Disassemble
793C Off-Highway Truck/Tractor Power Train Torque Converter - Assemble
784C, 785C and 785C HAA Off-Highway Truck Air System and Brakes Air Flow Schematic
554 Forwarder and 574 Forwarder Engine and Cab Preheat System - If Equipped
527 Track-Type Skidder Unhooking Winch Cable from Logs
D250E Series II and D300E Series II Articulated Trucks Power Train Rear Drive Axle - Remove
D250E Series II and D300E Series II Articulated Trucks Power Train Rear Drive Axle - Install
D250E Series II and D300E Series II Articulated Trucks Power Train Front Drive Axle - Remove
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Steering and Brake Manifold Valve - Disassemble
CB-434C, CB-534C and CB-634C Vibratory Compactors Water Spray System Machine Preparation for Troubleshooting