Cable (Heater Control) - Remove and Install
拆卸步骤
开始:
- 卸下驾驶室前挡板。 请参考拆卸和组装, "挡板(驾驶室前部)- 拆卸和安装"部分。
- 卸下六个大圆头螺钉 (1) 以从前仪表板上拆下仪表盘 (2) 。
注: 清洁度是一项重要的因素。 在执行拆卸操作之前,应彻底清洁部件外部。 这将有助于防止污垢进入内部机构。
Show/hide table
图 1 | g00520611 |
- 松开螺钉 (3) 和卡箍。 从加热器控制阀的控制杆上拆下电缆组件 (4) 。
Show/hide table
图 2 | g00520858 |
- 松开固定螺钉 (6) (未显示)以从电缆组件上卸下旋钮 (5) 。
Show/hide table
图 3 | g00520859 |
- 卸下仪表盘螺母 (7) 以从仪表盘 (2) 拆下电缆组件 (8) 。
Show/hide table
图 4 | g00520898 |
安装步骤
- 安装前确认电缆组件 (8) 的所有部件清洁无异物。
Show/hide table
图 5 | g00520898 |
- 检查所有部件是否磨损,必要时更换部件。
- 使用仪表盘螺母 (7) 将电缆组件 (8) 安装到仪表盘 (2) 上,如图所示。
- 将电缆组件的旋转开关 (8) 顺时针一直旋转到头。
- 将旋钮 (5) 安装到电缆组件的旋转开关上。 拧紧固定螺钉 (6) (未显示)以安装旋钮 (5) 。
Show/hide table
图 6 | g00520859 |
Show/hide table
图 7 | g00520858 |
- 关闭加热器控制阀。 将电缆组件 (4) 放置到加热器控制阀的控制杆上。
- 抚平电缆组件 (4) 上的所有松弛部分。
- 使用螺钉 (3) 和卡箍以安装电缆组件 (4) 。 拧紧螺钉 (3) 至扭矩 1.7 ± 0.25 牛米 (15.05 ± 2.21 磅英寸)。
- 使用六个大圆头螺钉 (1) 以将仪表盘 (2) 安装到前仪表板上。
Show/hide table
图 8 | g00520611 |
End By: 安装驾驶室前挡板。 请参考 拆卸和组装, "挡板(驾驶室前部)- 拆卸和安装"部分。
Caterpillar Information System:
784C and 785C Off-Highway Trucks Machine Systems Seat - Remove and Install
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Relay Valve (Brake) - Remove
784C and 785C Off-Highway Trucks Machine Systems Start Switch (Key) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Rotary Switch (Fan Speed) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Pressure Switch (Service Brake and Retarder) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Pressure Switch (Parking and Secondary Brake) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Magnetic Switch (Main Power) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Solenoid Valve (Air Horn) - Remove and Install
784C, 785C and 785C HAA Off-Highway Truck Air System and Brakes Hydraulic Tank (Torque Converter, Pulled Unit, Brake, and Transmission)
784C, 785C and 785C HAA Off-Highway Truck Air System and Brakes Hydraulic Tank (Torque Converter, Hoist, Brake, and Transmission)
784C, 785C and 785C HAA Off-Highway Truck Air System and Brakes Air/Hydraulic Cylinder (Brake)
583R Pipelayer Power Train Drive Shaft
784C and 785C Off-Highway Trucks Machine Systems Electronic Control Module (Power Train) - Remove and Install
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder - Assemble
3406E and 3456 Engines for Caterpillar Built Machines Fuel Pressure Sensor
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder Hydraulic Control Valve - Remove
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder Hydraulic Control Valve - Install
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder Hydraulic Control Valve - Disassemble
3176C and 3196 Engines for Caterpillar Built Machines Fuel System
527 Track-Type Skidder Power Train Transmission
527 Track-Type Skidder Power Train Transmission Controls and Parking Brake Linkage
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Position Sensor (Lift Arm) - Adjust
583R Pipelayer Power Train Transmission Mounting
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Pilot Accumulator - Remove and Install