Transmission Control - Install
- 安装之前先核实变速箱控制装置的所有部件清洁无异物。
- 检查所有部件是否磨损，必要时更换部件。
Show/hide table
图 1 g00483510 - 安装壳体 (14)、三个螺母 (13) 和硬垫圈。 此时不要拧紧螺母 (13)。
Show/hide table
图 2 g00483511 - 安装杆组件 (11)。 安装两条螺栓 (12) 和硬垫圈。 将杆组件 (11) 置于第四档位置。 必须校准正时标记 (15)。
Show/hide table
图 3 g00483506 - 将指示灯 (5) 连接至盖 (6)。
Show/hide table
图 4 g00483504 - 将两个软管组件 (4) 连接到空气控制阀上。 将盖降至原始位置。
Show/hide table
图 5 g00483601 - 将杆组件 (11) 移至倒档位置处槽的末端。 用塞尺测量杆组件和盖角之间的距离。 距离应该为
1.0 mm (0.04 in) 。Show/hide table
图 6 g00483621 - 拧紧三个螺母 (13)。
Show/hide table
图 7 g00849752 Show/hide table
图 8 g00484140 - 将板定位至变速箱控制装置上。 安装将板固定到变速箱控制装置上的两条螺栓 (9) 和垫圈。 将旋转位置传感器置于板上。 安装将旋转位置传感器固定至板上的两个机制螺钉 (10) 和垫圈。
注: 在配备较新的单件式旋转位置传感器的机器上，仅安装螺栓 (9)。 请参阅插图 7。
Show/hide table
图 9 g00483507 - 安装盖组件 (7)、四个大圆头螺钉 (8) 和垫圈。
Show/hide table
图 10 g00483480 - 将四个大圆头螺钉 (3) 安装在盖上。 将旋钮 (1) 安装到杆组件上。 拧紧调整螺钉 (2)。
Caterpillar Information System:
D250E Series II and D300E Series II Articulated Trucks 3306B Engine Supplement Engine Oil Cooler - Remove
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Transmission Control - Remove
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Main Hydraulic System
Electronic Modular Control Panel II (EMCP II) For MUI Engines Relay Module - Replace
D250E Series II and D300E Series II Articulated Trucks 3306B Engine Supplement Turbocharger - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations Switches
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Thermostat Switch (Cab) - Remove and Install
D250E Series II and D300E Series II Articulated Trucks 3306B Engine Supplement Fan Drive - Assemble
Electronic Modular Control Panel II (EMCP II) For MUI Engines EMCP Electronic Control (Generator Set) - Replace
789C Off-Highway Truck Steering System Steering Gear
D250E Series II and D300E Series II Articulated Trucks 3306B Engine Supplement Fan and Fan Drive - Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations General Information
D250E Series II, D300E Series II, D350E Series II and D400E Series II Articulated Trucks Power Train Electronic Control System CID 0702 FMI 03 Position Sensor (Shift Lever) Voltage Above Normal - Test
784B and 785B Off-Highway Truck Hydraulic System Hydraulic Tank (Torque Converter, Hoist, Brake, and Transmission)
C-10 and C-12 Industrial Engines Engine Oil Pan
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations Sensors
D250E Series II, D300E Series II, D350E Series II and D400E Series II Articulated Trucks Power Train Electronic Control System CID 0702 FMI 04 Position Sensor (Shift Lever) Voltage Below Normal - Test
D250E Series II, D300E Series II, D350E Series II and D400E Series II Articulated Trucks Power Train Electronic Control System CID 0704 FMI 03 Pressure Switch (Service Brake) Voltage Above Normal - Test
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Control Valve (Hoist) - Disassemble
3512B and 3516B Engine Supplement for and 784C,, 785C and and 785C HAA Off-Highway Truck/Tractors Engine and Torque Converter (High Altitude) - Remove
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Electric Drive Pump (Secondary Steering) - Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Display Modules
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Quad Gauge Module
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Speedometer/Tachometer Module