Transmission Control - Remove
开始:
- 释放气罐中的空气。 请参阅拆解和组装, "气罐（制动器）- 排气"。
Show/hide table
 |
|
车斗降下后，车斗与机架之间没有空隙。 如果不安装固定缆线，可能会导致在此区域作业的人员受伤或死亡。 |
- 在所有软管组件上作识别标记，以便于安装。
Show/hide table
图 1 g00483480 - 松开调整螺钉 (2) 并将旋钮 (1) 从杆组件上拆下。 将四个大圆头螺钉 (3) 从盖上拆下。
Show/hide table
图 2 g00483504 - 向上提起盖，以便于操作软管组件 (4)。 为便于安装，在软管组件 (4) 上作识别标记。 从空气控制阀上断开两个软管组件 (4)。
Show/hide table
图 3 g00483506 - 断开指示灯 (5) 并取下盖 (6)。
Show/hide table
图 4 g00483507 - 将四个大圆头螺钉 (8) 和垫圈从盖上拆下。 拆卸盖组件 (7)。
Show/hide table
图 5 g00849752 Show/hide table
图 6 g00484140 - 拆卸将旋转位置传感器固定至板上的两个机制螺钉 (10) 和垫圈。 拆卸将板固定到变速箱控制装置上的两条螺栓 (9) 和垫圈。
注: 在配备较新的单件式旋转位置传感器的机器上，仅拆卸螺栓 (9)。 请参阅插图 5。
Show/hide table
图 7 g00483509 - 拆下两条螺栓 (12) 和硬垫圈。 拆卸杆组件 (11)。
Show/hide table
图 8 g00483510 - 拆下三个螺母 (13) 和硬垫圈。 取下壳体 (14)。
注: 将盖和塞安装在全部孔口上，以免污垢或碎屑进入系统。 清洁度是一项重要的因素。 拆卸步骤开始之前，应彻底清洁部件外部。 这将防止脏污进入内部部件。
Caterpillar Information System:
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Main Hydraulic System
Electronic Modular Control Panel II (EMCP II) For MUI Engines Relay Module - Replace
D250E Series II and D300E Series II Articulated Trucks 3306B Engine Supplement Turbocharger - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations Switches
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Thermostat Switch (Cab) - Remove and Install
D250E Series II and D300E Series II Articulated Trucks 3306B Engine Supplement Fan Drive - Assemble
Electronic Modular Control Panel II (EMCP II) For MUI Engines EMCP Electronic Control (Generator Set) - Replace
789C Off-Highway Truck Steering System Steering Gear
D250E Series II and D300E Series II Articulated Trucks 3306B Engine Supplement Fan and Fan Drive - Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations General Information
D250E Series II, D300E Series II, D350E Series II and D400E Series II Articulated Trucks Power Train Electronic Control System CID 0701 FMI 08 Speed Sensor (Transmission Output) Abnormal Signal - Test
IT62G Series II Integrated Toolcarrier Pallet Fork Rated Load
D250E Series II and D300E Series II Articulated Trucks 3306B Engine Supplement Engine Oil Cooler - Remove
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Transmission Control - Install
D250E Series II, D300E Series II, D350E Series II and D400E Series II Articulated Trucks Power Train Electronic Control System CID 0702 FMI 03 Position Sensor (Shift Lever) Voltage Above Normal - Test
784B and 785B Off-Highway Truck Hydraulic System Hydraulic Tank (Torque Converter, Hoist, Brake, and Transmission)
C-10 and C-12 Industrial Engines Engine Oil Pan
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations Sensors
D250E Series II, D300E Series II, D350E Series II and D400E Series II Articulated Trucks Power Train Electronic Control System CID 0702 FMI 04 Position Sensor (Shift Lever) Voltage Below Normal - Test
D250E Series II, D300E Series II, D350E Series II and D400E Series II Articulated Trucks Power Train Electronic Control System CID 0704 FMI 03 Pressure Switch (Service Brake) Voltage Above Normal - Test
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Control Valve (Hoist) - Disassemble
3512B and 3516B Engine Supplement for and 784C,, 785C and and 785C HAA Off-Highway Truck/Tractors Engine and Torque Converter (High Altitude) - Remove
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Electric Drive Pump (Secondary Steering) - Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Display Modules