Speed Sensor (Engine) - Adjust
Show/hide table
 | |
| Illustration 1 | g00289497 |
Speed Sensor (1) Speed sensor (2) Locknut (A) Air gap | |
This adjustment procedure is for the engine speed sensor.
- Remove the speed sensor (1) from the flywheel housing. Remove all debris from the tip of the speed sensor. Align a ring gear tooth directly in the center of the threaded sensor opening.
- By hand, screw the speed sensor (1) into the hole until the end of the sensor contacts the gear tooth.
- Turn the sensor (1) in the counterclockwise direction through 270 degrees (three-fourths turn).
- Tighten locknut (2) to 25 ± 5 N·m (18 ± 4 lb ft).
Note: Do not allow speed sensor (1) to turn as locknut (2) is tightened.
Caterpillar Information System:
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Sensors
784C and 785C Off-Highway Truck/Tractors Transmission Tank Suction Screen - Clean/Inspect/Replace
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Air Tank (Primary) - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines Alarm Module Control - Adjust
D250E Series II, D300E Series II, D350E Series II and D400E Series II Articulated Trucks Power Train Electronic Control System CID 0420 FMI 06 Relay (Secondary Steering) Current Above Normal - Test
784C and 785C Off-Highway Truck/Tractors Hoist, Torque Converter and Brake Tank Suction Screen - Inspect/Clean/Replace
D250E Series II, D300E Series II, D350E Series II and D400E Series II Articulated Trucks Power Train Electronic Control System CID 0420 FMI 05 Relay (Secondary Steering) Current Below Normal - Test
561M Pipelayer Priority Valve
3116 Engine for Challenger 35, Challenger 45 Agricultural Tractors and 3126 Engine for Challenger 55 Agricultural Tractor Engine Supplement Water Temperature Regulator - Remove and Install
3116 Engine for Challenger 35, Challenger 45 Agricultural Tractors and 3126 Engine for Challenger 55 Agricultural Tractor Engine Supplement Water Pump - Install
3116 Engine for Challenger 35, Challenger 45 Agricultural Tractors and 3126 Engine for Challenger 55 Agricultural Tractor Engine Supplement Water Pump - Remove
3116 Engine for Challenger 35, Challenger 45 Agricultural Tractors and 3126 Engine for Challenger 55 Agricultural Tractor Engine Supplement V-Belts - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines Charging System - Test
69D and 769D Off-Highway Trucks and 771D Quarry Truck Water Temperature Regulator - Remove
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Control Valve (Hoist) - Remove
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Main Control Valve (Lift and Auxiliary)
980G Wheel Loader Braking System Parking Brake - Test
D250E Series II, D300E Series II, D350E Series II and D400E Series II Articulated Trucks Power Train Electronic Control System CID 0444 FMI 03 Magnetic Switch (Start Relay) Voltage Above Normal - Test
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Power Train Duo-Cone Conventional Seals - Install
D250E Series II and D300E Series II Articulated Trucks 3306B Engine Supplement Fan Drive - Disassemble
69D and 769D Off-Highway Trucks and 771D Quarry Truck Water Temperature Regulator - Install
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Power Train Covers - Remove and Install
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Power Train Belt - Detension and Tension
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Power Train Belt - Remove and Install