Engine Front Support - Remove
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | FT-1321 | Support Beam | 1 |
A | 1D-4706 | Bolt (3/8 inch - 16 NC X 6 inch long) | 1 |
B | 4C-6928 | Air/Hydraulic Jack | 1 |
Start By:
- Remove the engine oil pan. Refer to Disassembly and Assembly, "Oil Pan - Remove".
- Remove the fan drive. Refer to Disassembly and Assembly, "Fan Drive - Remove".
- Remove the vibration damper. Refer to Disassembly and Assembly, "Vibration Damper - Remove and Install".
- Install Tooling (A) to the bottom of the cylinder block assembly.
- Position Tool (B) under the mid-position of Tool (A).
Show/hide table
Illustration 2 g00488403 - Remove four bolts (1), the hard washers and the full nuts that hold front engine support (2) to support assembly (3).
Show/hide table
Illustration 3 g00586034 Right Side - Loosen two full nuts (4) on the mount assembly.
Show/hide table
Illustration 4 g00586063 Left Side - Loosen two full nuts (5) on the mount assembly.
Show/hide table
Illustration 5 g00586085 - Use Tool (B) (not shown) to raise front engine support (2)
3.18 to 6.35 mm (0.125 to 0.25 inch) above the support assembly. - Remove four bolts (6) and the hard washers that hold front engine support (2) to the engine trunnion. Remove front engine support (2) from the engine trunnion.
Show/hide table
Illustration 1 | g00488401 |
Caterpillar Information System:
69D and 769D Off-Highway Trucks and 771D Quarry Truck Oil Cooler (Hoist and Rear Brake) - Install
69D and 769D Off-Highway Trucks and 771D Quarry Truck Oil Cooler (Hoist and Rear Brake) - Remove
3306C Engines for Caterpillar Built Machines Ether Starting Aid
572R Pipelayer Hydraulic System Combination Valves
69D and 769D Off-Highway Trucks and 771D Quarry Truck Engine Oil Cooler - Install
572R Pipelayer Hydraulic System Boom
AP-1055B and BG-2455C Asphalt Pavers Screed Hoist Control
572R Pipelayer Hydraulic System Pipelayer Frame Group
Electronic Modular Control Panel II (EMCP II) For MUI Engines Indicator for Engine Overspeed - Troubleshoot
69D and 769D Off-Highway Trucks and 771D Quarry Truck Electronic Control Module (Engine) - Remove and Install
69D and 769D Off-Highway Trucks and 771D Quarry Truck Cooling System Pressure Relief Valve - Remove and Install
69D and 769D Off-Highway Trucks and 771D Quarry Truck Turbocharger - Install
69D and 769D Off-Highway Trucks and 771D Quarry Truck Fan Drive - Remove
IT14G Integrated Toolcarrier Window Wiper - Inspect/Replace
572R Pipelayer Hydraulic System Load Sense Manifold
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Three-Point Hitch Control Valve
Electronic Modular Control Panel II (EMCP II) For MUI Engines Troubleshooting Undiagnosed Problems
789C Off-Highway Truck/Tractor Gear Pump (Transmission)
517 Track-Type Skidder Hydraulic System Testing and Adjusting
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Hydraulic Tank - Install
G3B, K3A and L3A Denso Alternators Alternator - Assemble
CP-563D, CS-563D, CS-573D and CS-583D Paving Compactors Engine Air Filter Primary Element - Clean/Replace
789C Off-Highway Truck/Tractor Pressure Sensor (Rear Axle Oil Pump)
69D and 769D Off-Highway Trucks and 771D Quarry Truck Fan Drive - Disassemble