Cab - Tilt
Park the machine on a level surface. Ensure that the parking brake is fully engaged. Lower the dump body and stop the engine.
The machine has a tilt cab. The tilt cab allows easier access to the following components:
- The engine
- The torque converter
- The transmission
Raise the Cab
- Raise the hood. Remove eight bolts (1) and the washers. Remove hydraulic tank cover (2) .
Show/hide table
Illustration 1 | g00339595 |
- Remove bolt (3) and the washer.
Show/hide table
Illustration 2 | g00339573 |
- Remove three bolts (4) and the washers. Remove guard (5) .
Show/hide table
Illustration 3 | g00339494 |
- Remove four bolts (6) and the washers. Remove cover plate (7) .
Show/hide table
Illustration 4 | g00339655 |
- Remove center bolt (8) and the washer. Loosen two outer bolts (9). Remove step (10) .
Show/hide table
Illustration 5 | g00644909 |
- Remove spring clip (11) and remove pin (12) from the right front of the cab.
Show/hide table
Illustration 6 | g00644911 |
- Remove spring clip (13) and remove pin (14) from the left front of the cab.
Show/hide table
Illustration 7 | g00644913 |
- Turn pump control (21) clockwise until the valve is fully closed. Position handle (15) into hydraulic hand pump (16) and operate the handle in order to raise the cab. The pump handle is stored in the toolbox.
Show/hide table
NOTICE |
---|
Ensure that all lines and wires are clear of any obstructions before tilting the cab. |
Show/hide table
Illustration 8 | g00644914 |
- When the cab is raised, install pin (17) through the hole in cab support (18).
Show/hide table
Illustration 9 | g00644915 |
- Continue to raise the cab and install pin (19) through cylinder support (20). Turn the pump control (21) slowly in a counterclockwise direction in order to lower the cab and allow the cab to be supported by cylinder support (20). Turn pump control (21) clockwise. Remove handle (15) .
Show/hide table
Illustration 10 | g00644916 |
Lower the Cab
- Turn pump control (21) clockwise. Raise the cab sufficiently in order to allow pin (19) and pin (17) to be removed.
- Turn pump control (21) slowly in a counterclockwise direction in order to lower the cab. Remove handle (15) and return the handle to the toolbox.
- Install pin (14) and spring clip (13) into the left front of the cab.
- Install pin (12) and spring clip (11) into the right front of the cab.
- Position step (10). Install one bolt (8) and the washer. Tighten two bolts (9) .
- Position cover plate (7). Install four bolts (6) and the washers.
- Position guard (5). Install three bolts (4) and the washers.
- Install bolt (3) and the washer.
- Position hydraulic tank cover (2). Install eight bolts (1) and the washers.
- Lower the hood.
Caterpillar Information System:
3406E and 3456 Engines for Caterpillar Built Machines Electronic Control System Components
IT14G Integrated Toolcarrier Lifting and Tying Down the Machine
IT14G Integrated Toolcarrier Equipment Lowering with Engine Stopped
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Main Control Valve (Tilt and Auxiliary)
572R Pipelayer Hydraulic System Hydraulic Pump
CP-563D, CS-563D, CS-573D and CS-583D Vibratory Compactors Vibratory System Vibratory Magnetic Sensor - Test and Adjust
CP-563D, CS-563D and CS-583D Vibratory Compactors Leveling Blade Hydraulic Cylinder (Leveling Blade) - Test
IT14G Integrated Toolcarrier Alternate Exit
980G Wheel Loader Braking System Brake Control Valve (Service)
966G Wheel Loader and 972G Wheel Loader Hydraulic System Main Control Valve
IT14G Integrated Toolcarrier Cab Door
IT14G Integrated Toolcarrier Steering Frame Lock
793C Off-Highway Truck Machine Systems Fuel Tank - Install
69D and 769D Off-Highway Trucks and 771D Quarry Truck Alternator - Remove and Install
IT14G Integrated Toolcarrier Attachment Arm and Cylinder Linkage - Lubricate
CP-563D, CS-563D, CS-573D and CS-583D Vibratory Compactors Propel System Travel Speed - Check
69D and 769D Off-Highway Trucks and 771D Quarry Truck Refrigerant Accumulator - Remove and Install
980G Wheel Loader Braking System Service Brakes
D350E Series II Articulated Truck Hoist Control Valve - Disassemble
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Pilot Control Valve - Remove
IT14G Integrated Toolcarrier Fuel Tank Water and Sediment - Drain
IT14G Integrated Toolcarrier Hydraulic System Oil - Change
CP-563D, CS-563D, CS-573D and CS-583D Vibratory Compactors Vibratory System Variable Frequency Electrical Control - Test and Adjust - If Equipped
69D and 769D Off-Highway Trucks and 771D Quarry Truck Refrigerant Compressor - Remove and Install