Lift Kickout Positioner - Adjust
Show/hide table
 |
Use caution to avoid possible personal injury when adjusting the attachment lift kickout. Keep personnel off the machine. Clear the area when working under or around the attachment linkage. With the attachment raised, proper support must be provided for the attachment and/or the linkage. |
 |
- Start the engine. Raise the bucket or attachment to the desired lift kickout height and stop the engine.
- Loosen nuts (4). Adjust switch assembly (1) so that the lower edge of magnet (3) is even with the center of switch assembly (1) .
Show/hide table
 | |
| Illustration 1 | g00495490 |
(1) Switch assembly (2) Bolts (3) Magnet (4) Nuts | |
- Tighten nuts (4) .
- Loosen bolts (2). Adjust switch assembly (1) so that the face is 8 ± 2 mm (.32 ± .08 inch) away from magnet (3) .
- Tighten bolts (2) .
- To check the adjustment, start the engine. Move the lift lever to the RAISE detent position.
When the bucket or attachment reaches the preset lift height, the lift lever should return to the HOLD position.
- If the kickout position is not correct, perform Steps 1 through 6 again.
Caterpillar Information System:
CP-563D, CS-563D, CS-573D and CS-583D Vibratory Compactors Vibratory System Vibratory Electrical System
D6R Track-Type Tractor Power Train Track Idler
3208 Marine Engine Fuel System Water Separator - Drain
793C Off-Highway Truck Machine Systems Gear Pump (Brake Release and Oil Cooling) - Assemble
65E, 75E, 85E and 95E Agricultural Tractors Windshield Wiper and Washer Control
65E, 75E, 85E and 95E Agricultural Tractors Warning Alarm
D250E Series II and D300E Series II Articulated Trucks Circuit Breakers - Reset
D250E Series II and D300E Series II Articulated Trucks Cab Air Filter - Clean/Replace
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Parking Brake Control - Adjust
793C Off-Highway Truck Machine Systems Gear Pump (Brake Release and Oil Cooling) - Disassemble
D7R Track-Type TractorPower Train Track Roller Frame
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Lift Cylinder - Install
D250E Series II and D300E Series II Articulated Trucks Cooling System Coolant (DEAC) - Change
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head Additional Reference Material
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Attachment Positioner - Adjust
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head Hydraulic System Pressure Reducing Valve (Back Pressure)
D7R Track-Type TractorPower Train Track Carrier Roller
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Power Train Transmission Charge Pump
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Kickout System - Integrated Toolcarriers
D250E Series II and D300E Series II Articulated Trucks Cooling System Coolant (ELC) - Change
980G Wheel Loader Braking System Accumulator Charging Valve (Brake)
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Switches
D250E Series II and D300E Series II Articulated Trucks Cooling System Level - Check
D250E Series II and D300E Series II Articulated Trucks Cooling System Pressure Cap - Clean/Replace