Tilt Link - Remove
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 3S-6224 | Electric Hydraulic Pump Gp | 1 |
6V-3175 | Double Acting Cylinder | 1 | |
4C-9634 | Puller Stud | 1 | |
9U-6832 | Nut | 1 | |
6V-4035 | Sleeve | 1 | |
B | 3S-6224 | Electric Hydraulic Pump Gp | 1 |
6V-3175 | Double Acting Cylinder | 1 | |
6V-4035 | Sleeve | 1 | |
4C-9634 | Puller Stud | 1 | |
9U-6832 | Fast Runner Nut Assembly | 1 | |
C | 3S-6224 | Electric Hydraulic Pump Gp | 1 |
6V-3175 | Double Acting Cylinder | 1 | |
4C-9634 | Puller Stud | 1 | |
9U-6832 | Fast Runner Nut Assembly | 1 | |
5P-8601 | Bearing Puller Adapter | 1 | |
7F-6068 | Sleeve Assembly | 1 |
Start By:
- Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
- Stop the machine so that the bucket is positioned flat on the ground.
Show/hide table
Illustration 1 g00391837 - Attach a suitable lifting device to bucket tilt link (1). The weight of bucket tilt link (1) is approximately
54 kg (120 lb) . - Remove bolt (2), the washer, and the spacer from pin assembly (3).
Show/hide table
Illustration 2 g00880756 - Attach a suitable lifting device to Tooling (A). The weight of Tooling (A) is approximately
34 kg (75 lb) . - Use Tooling (A) to remove pin assembly (3).
Show/hide table
Illustration 3 g01202012 - Reposition the suitable lifting device on tilt link (1), as shown.
Show/hide table
Illustration 4 g00348514 - Remove bolt (4), the washer, and the spacer from pin assembly (5).
Show/hide table
Illustration 5 g00348515 - Use Tooling (B) in order to remove pin assembly (5).
- Use the suitable lifting device in order to remove bucket tilt link (1).
Show/hide table
Illustration 6 g00348516 - Remove lip seals (6) from both sides of bucket tilt link (1). Repeat this step for the opposite end of the bucket tilt link (1).
Show/hide table
Illustration 7 g00348652 - Use Tooling (C) in order to remove the bearing from bucket tilt link (1). Repeat this step for the opposite end of bucket tilt link (1).
Caterpillar Information System:
TK711, TK721, TK722 and TK732 Track Feller Bunchers Track Adjustment - Inspect
307B Excavator Track Adjustment - Adjust
517 Track-Type Skidder Lifting and Tying Down the Machine
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Check Valve
784B Tractor and 785B Off-Highway Truck Power Train Lockup Clutch and Synchronizing Valve (Torque Converter)
527 Track-Type Skidder Shipping the Machine
Air Conditioning and Heating R134a for All Caterpillar Machines Refrigerant Expansion Valve System
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Warning Signs and Labels
539 Knuckleboom Loader Fuses - Replace
539 Knuckleboom Loader Engine Oil and Filter - Change
539 Knuckleboom Loader Engine Oil Level - Check
539 Knuckleboom Loader Engine Air Precleaner - Clean
3516B and 3516B High Displacement Engines for 994D and 994F Wheel Loaders Flywheel Housing Cover
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Swing Drawbar
784B Tractor and 785B Off-Highway Truck Power Train Torque Converter
793B Off-Highway Truck Power Train Drive Shaft (Main)
3516B and 3516B High Displacement Engines for 994D and 994F Wheel Loaders Auxiliary Drive (Lower Left Hand)
527 Track-Type Skidder Towing the Machine
CP-563C and CS-563C Vibratory Compactors Mirror - If Equipped
3500B Engines for Excavators Engine Oil Scavenge Pump
CP-563C and CS-563C Vibratory Compactors Window (Side Sliding)
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Steering Wheel
CP-563C and CS-563C Vibratory Compactors Alternate Exit
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Priority Valve