Contour Seat With Front Controls - Assemble
安装程序
- 检查体形系列座椅所有零件的状况。 如果发现某些零件磨损或损坏,就用新零件将其更换。
- 在座椅盘组合安装钢丝绳组合 (43) 。 安装铆钉 (44) 。
Show/hide table
图 1 | g00275687 |
- 在上部滑板的底部 (16 ) 安装2只托座 (42) , 防松螺母和6只螺栓 (41) 。
Show/hide table
图 2 | g00275686 |
- 在上部滑板 (16) 安装滑动手柄/锁定轴 (39) 和弹簧 (40) 。 安装销子 (38) 。 挂上弹簧 (40) 。
Show/hide table
图 3 | g00275685 |
- 在上部滑板 (16) 安装手柄组合 (34) 安装2只护圈夹头 (33) 。
Show/hide table
图 4 | g00275684 |
Show/hide table
图 5 | g00275683 |
- 在杆件组合 (35) 安装手柄 (37) 。 装配手柄组合 (34) 安装4只螺丝 (36) ,把前后定位。
- 在座椅盘组合安装座椅倾斜杆组合 (31) 。 把弹簧 (25) 滑入杆件内. 在坐垫倾斜杆组合 (31) 安装3只滚动销子 (30) 。 把弹簧 (25) 挂到滚动销子上。 在坐垫倾斜杆组合 (31) 安装手柄 (29) 。
Show/hide table
图 6 | g00275682 |
- 在座椅盘组合,为坐垫调整,安装杆件组合 (27) 。 把弹簧 (28) 滑入杆件内。 把杆件滑入座椅的内侧,使杆件与内部的拉环 (B) 合紧。 把滚动销子 (26) 装在杆件组合 (27) 。 把手柄 (32) 装在杆件组合 (27) 。
- 安装衬套,隔离环和左侧扶手 (22) 。 安装螺栓 (23) 和防松垫圈。 安装螺栓 (24) 。
Show/hide table
图 7 | g00275681 |
注: 取下扶手的同时,也把背部围板和弹簧卸下。
- 使用步骤9的程序安装右侧扶手。
- 为椅背,把调整器 (17) 挂到钢丝绳上 (21) 并安装护圈夹头 (20) 。 安装护圈夹头 (20) 和钢丝绳 (21) 成为 杆件整体。
Show/hide table
图 8 | g00275680 |
- 在每只调整器 (17) 末端,安装销子 (19) 和护圈夹头 (18)
Show/hide table
图 9 | g00275679 |
- 提起杆件 (A) 使靠背向后转。
- 在上部滑板 (16) 安装座椅靠背和座盘组合 (15) 。 安装6只螺栓 (13) 和 (14) 。 安装2只螺栓 (12) 和防松螺母。
Show/hide table
图 10 | g00275678 |
- 安装安全带牵拉装置 (11) 。 安装用于把座椅安全带牵拉装置 (11) 固定在座椅上的螺栓。 安装舒适乘坐轴套 (9) 。 安装把舒适乘坐轴套 (9) 固定在座椅上的螺母和螺栓 (10) 。
Show/hide table
图 11 | g00275677 |
- 在板上安装2只弹簧 (7) 。 把坐垫倾斜杆 (8) 往上提,并安装面板 (6) 。 把面板 (6) 按下,再安装 2只开尾销 (5) 。
Show/hide table
图 12 | g00275676 |
Show/hide table
图 13 | g00275635 |
Show/hide table
安装座椅倾斜板的时候,弹簧力顶住倾斜板。 为避免伤害,安装时,用手把持倾斜板。 |
- 在座椅倾斜盘上安装座底软垫 (4) 。
Show/hide table
图 14 | g00275634 |
- 在座椅靠背安装座椅软垫 (3) 。
Show/hide table
图 15 | g00275633 |
- 在座椅组合安装2只衬套 (2) 为安装衬套,把每只衬套顺时针旋转 1/4圈。
Show/hide table
图 16 | g00275632 |
- 在座椅组合安装椅背伸出件 (1) 。 靠背外伸件是滑配安装。
Show/hide table
图 17 | g00275631 |
- 座椅安装完毕之后,把钢丝绳调整到正确位置。 用调整器 (17) 调整钢丝绳。 钢丝绳不能太紧。 钢丝绳应该有些松弛。 座椅倾斜之前,钢丝绳应该稍微松动。
Show/hide table
图 18 | g00713003 |
- 在机器上安装体形系列座椅。
Caterpillar Information System:
Contour Series Seat Contour Seat With Front Controls - Disassemble
Contour Series Seat Contour Seat Controls
Contour Series Seat Contour Seat Air Suspension with Air System
784C, 785C and 785C HAA Off-Highway Truck/Tractors Steering System Pressure Switch (Steering Pump Oil)
3406E Truck Engine Connecting Rod
Torque Specifications Installation of Fittings
Torque Specifications O-Ring Face Seal Fittings
Contour Series Seat Contour Seat Air Suspension with Air Compressor
Caterpillar<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> AP-650B and Barber-Greene<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> BG-225C Asphalt Pavers Air Inlet Heater Starting Aid
Torque Specifications Straight Thread O-Ring Fittings
416C, 426C, 428C, 436C and 438C Backhoe Loaders Axles, Differential and Brakes Drive and Steering Axle (Rear)
3406E and 3456 Industrial Engines Rocker Shaft
Contour Series Seat Contour Seat With Lumbar Option and Side Controls - Disassemble
554 Forwarder and 574 Forwarder Engine Valve Lash - Check
554 Forwarder and 574 Forwarder Fuel Injection Timing - Check
Contour Series Seat Contour Seat With Lumbar Option and Side Controls - Assemble
561M Pipelayer Torque Converter
561M Pipelayer Torque Converter Operation
3406C Engines for Caterpillar Built Machines Connecting Rod Bearing Journal
793C Off-Highway Truck Hydraulic System Hoist and Brake Cooling Hydraulic System Troubleshooting
784B and 785B Off-Highway Truck/Tractors Steering System Front Wheel
Contour Series Seat Swivel Seat - Disassemble
Comfort Series Seat For Caterpillar Machines Swivel Seat - Assemble
793B Off-Highway Truck Power Train Rear Axle Housing End Play - Adjust