Use FT2594 Seal Installer For Correct Cone Seal Installation {7561}
Usage:
CS533C (2WN, 2XN),
CP/CS563C (4KN, 4LN),
CS573C (6LN),
CS583C (7MN, 7NN) Vibratory Compactors
Warranty: None
Features/Benefits
-
- * Essential Tool
- * Used to install Duo-cone seals in propel drive motors
- * Made from 126-3994 Installer, Seal Assembly
- * Seals cannot be correctly installed using any other tooling
- * Provides fast and easy installation
- * Prevents seal rolling and twisting
- * Essential Tool
Specifications/Technical Information
For use on 7T-2459 Seal Group:
- Toric cross section - 12.7 mm (.50 in)
- Seal ramp angle - 15 degrees
Procedure
-
- (1) Remove four screws (2).
- (2) Cut 54 mm (2.1 in) - (Dimension B) from the circumference of item (1).
- (3) Drill and tap four holes for screws (2), Maintain dimension C and D, and attach inner sliding member (3). Make sure alignment of installer edges is maintained.
- (4) Make sure screws (2) do not extend more than 0.5 mm (.02 in) through installer (1).
- (5) Remove old part number and mark new part number.
- (1) Remove four screws (2).
FT2594 Seal Installer Assembly
Reference
SEHS8364; Special Instruction, Assembly and Installation of Conventional Duo-Cone Seals; SEHS8484; Special Instruction, Tool and Specification Chart for Conventional Duo-Cone Seals
Caterpillar Information System:
1998/09/21 New Plug Kit Improves Injection Actuation Pressure During Engine Cranking {1714}
1998/09/21 Recommended Lubrication And Torque Procedure For Main Bearing Cap Bolts {1203}
1998/09/21 Recommended Lubrication And Torque Procedure For Connecting Rod Bolts {1218}
1998/09/21 Recommended Lubrication And Torque Procedure For Cylinder Head Bolts {1100}
1998/09/21 Correction To Testing And Adjusting Manual, SENR6785-01 And Specifications Manual, SENR6703 {0374,3155}
1998/09/14 New Torque Value For Lug Nut On Drive Wheels{4209,4210}
1998/09/14 New 1U-8660 Hydraulic Unit Boring Bar, 9U-5730 Portable Boring Bar (110 Volt), And 9U-5889 Portable Boring Bar (220 Volt) Now Available{0679}
1998/09/14 Use FT2563 Adjustment Tool For Assembly Of Limited-Slip Differential{3263}
1998/09/14 Improved Laser Hardened Spindles Used In Certain Off-Highway Trucks{4205,4234}
1998/09/14 Updated Assembly Procedure For 777D Off-Highway Trucks Is Available{7960,7006}
1998/09/14 New Clutches Reduce Drag And Improve Efficiency{3030,3155}
1998/09/07 New Serial Number Prefix {0374}
1998/09/28 New Gear And New Shaft Assemblies Used In Scavenge Oil Pump Groups {1312}
1998/09/28 New Spacer Plate Gasket Provides Improved Sealing {1221}
1998/09/28 New Larger Engine Scavenge Oil Pump Provides More Oil Flow {1312}
1998/09/28 Adjustment Procedure For Differential Bevel Gear Backlash And Preload {0351,3256,3258,3270}
1998/09/28 Cover Protects Fuse Panel {1417}
1998/09/28 New Spring Assembly For Transmission Control Improves Service Life {3073}
1998/09/28 New Transmission Control Group And Flash Software Available, Featuring Improved Downshifting {3168}
1998/09/28 New Implement Control Groups Available With Numerous Enhancements {7490}
1998/09/28 Proper Flasher Wiring for 928G Wheel Loaders & IT28G Integrated Toolcarriers {1430}
1998/09/28 Maintenance Of The Self Dumping Bucket {5000,5059}
1998/09/28 Correction To Telehandler Parts Manual {7051}
1998/09/28 Hydraulic Tank Refill Capacities For Telehandlers {5056}