Machine Drift on a Slope - Check
Show/hide table
Drift | |||
Item | Specification | Time (min) | Slope (deg) |
Maximum Drift | |
3 | 12 |
Note: The engine speed and/or the machine configuration that is used during this test can affect the results of this test.
Reference: Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for the engine speed that was used for this test.
Reference: Testing and Adjusting, "Operational Checks" for the machine configurations that were used for this test.
The relief valve pressure settings must be set to the relief valve pressure specification before performing this operational check.
Reference: Testing and Adjusting, "Specifications".
Measuring the amount of drift of the machine on a slope will determine if there is a need to check the travel brake.
Show/hide table
Required Tools | |
---|---|
Description | Qty |
Tape Measure | 1 |
Stopwatch | 1 |
- Place the machine on a slope of 12 degrees. Refer to Illustration 1.
- The surface must be hard.
Show/hide table
Illustration 2 g06278080 (A) Mark on roller frame
(B) Mark on track - To indicate the relative position of the machine to the slope, put a mark on both the roller frame and the track.
Show/hide table
Illustration 1 | g06365047 |
(A) 12 degrees |
- Ensure that bucket is empty.
- Start the engine.
- Increase the hydraulic oil temperature to
55° ± 5°C (131° ± 9°F) .
- Position the implements, as shown. Refer to Illustration 1.
- Fully extend the stick cylinder and the bucket cylinder.
- Stop the engine.
- Measure the machine movement on the slope after 3 minutes.
- Refer to Table 1 for specification.
Caterpillar Information System:
325 Excavator Joystick Controls
325 Excavator Declaration of Conformity
325 Excavator Plate Locations and Film Locations
Rework Procedure for the Fuel Filter Housing on Certain Machine Engines {1261} Rework Procedure for the Fuel Filter Housing on Certain Machine Engines {1261}
C9.3B Industrial Engines Engine Oil Pan - Install
325 Excavator Lifting Capacities
New Bolts are Now Used for the Fuel Filter Support Bracket on Certain C18 Marine Engines {1260} New Bolts are Now Used for the Fuel Filter Support Bracket on Certain C18 Marine Engines {1260}
325 Excavator Boom/Stick/Bucket Combinations
325 Excavator Specifications
A New Vent Line is Now Used on Certain C175-16 Generator Sets {1380} A New Vent Line is Now Used on Certain C175-16 Generator Sets {1380}
3516E Generator Sets General Maintenance Information
3516E Generator Sets Fluid Recommendations
325 Excavator Capacities (Refill)
325 Excavator Fuses - Replace
325 Excavator Maintenance Interval Schedule
New EC520 Controller Monitor Software is Now Available for Cat® Grade System {7220, 7490, 7601, 7610, 7620} New EC520 Controller Monitor Software is Now Available for Cat® Grade System {7220, 7490, 7601, 7610, 7620}
New EC520 Controller Monitor Software is Now Available for Cat® Grade System {7220, 7490, 7601, 7603, 7610, 7620} New EC520 Controller Monitor Software is Now Available for Cat® Grade System {7220, 7490, 7601, 7603, 7610, 7620}
Improved Air Filter Element Assembly Is Now Used on Certain Excavators, Forest Machines, and Mobile Hydraulic Power Units {1051, 1054, 105A} Improved Air Filter Element Assembly Is Now Used on Certain Excavators, Forest Machines, and Mobile Hydraulic Power Units {1051, 1054, 105A}
323D3 ExcavatorTA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} 323D3 ExcavatorTA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
320D3 ExcavatorTA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} 320D3 ExcavatorTA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
307.5, 308, 308.5, 309, and 310 Mini Hydraulic Excavators Diesel Particulate Filter Regeneration
140 Motor Grader Power Train Transmission - Remove and Install
140 Motor Grader Systems Machine Preparation
140 Motor Grader Systems System Pressure - Release