Swivel - Assemble
- Install plug (11) into rotor (8).
Show/hide table
Illustration 2 g02102477 - Install O-ring seals (9) and seals (10) into housing (7). Lubricate O-ring seals (9) and seals (10) with lubricant that is being sealed.
Show/hide table
Illustration 3 g02103125 - Lubricate the sealing surface of rotor (8) with lubricant that is being sealed. Use two people in order to install housing (7) onto rotor (8). The weight of housing (7) is approximately
25 kg (55 lb) . The weight of rotor (8) is approximately23 kg (50 lb) . Carefully install housing (7) onto rotor (8).Show/hide tableIllustration 4 g02102475 - Install retainer (6), washers (5), and bolts (4).
Show/hide table
Illustration 5 g02102474 - Install O-ring seal (3), cover (2), and bolts (1).
Show/hide table
Illustration 6 g02103143 Port reference for the rotor and the housing. Note: Open all the ports except for the port that is being tested.
- Check the swivel for leaks. Plug the drain ports of the inside body. Apply shop air pressure in the top of the swivel and check the swivel for leaks. The shop air pressure should be
414 to 483 kPa (60 to 70 psi) . Ensure that the pressure does not drop7 kPa (1 psi) in twenty seconds.
Show/hide table
Illustration 1 | g02102478 |
End By:
- Install the swivel.
Caterpillar Information System:
320D3 Hydraulic Excavator Machine Systems Swivel - Disassemble
320D3 Excavators Maintenance Interval Schedule
320D3 Excavators Fuel Lift Pump Strainer - Replace
320D3 Excavators Hydraulic System Oil Filter (Pilot) - Replace
320D3 Excavators Hydraulic System Oil Filter (Case Drain) - Replace
320D3 Excavators Fuel System Water Separator - Drain
320D3 Excavators Fuel System Secondary Filter - Replace
320D3 Excavators Fuel System Primary Filter (Water Separator) Element - Replace
797F Tier 4 Off-Highway Truck Engine Supplement Voltage Control (Load Protection) - Remove and Install
320D3 and 323D3 Excavators Systems Main Electrical System
320D3 Hydraulic Excavator Machine Systems Heating and Air Conditioning Unit - Remove and Install
320D3 and 323D3 Excavators Systems Travel Counterbalance Valve
797F Tier 4 Off-Highway Truck Engine Supplement Nitrogen Oxide Sensor (Exhaust Outlet) - Remove and Install
C175 Tier 4 Final Engines for Caterpillar Built Machines Water Pump - Assemble
Engine Storage and Engine Start-Up After Storage {1000, 1300, 1348, 7418} Engine Storage and Engine Start-Up After Storage {1000, 1300, 1348, 7418}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Quick Coupler Operation - If Equipped
C18 Generator set and C18 Marine Engines Fuel Filter Base - Remove and Install
The Hydraulic Tank is Improved on Certain 797F Off-Highway Trucks {5056} The Hydraulic Tank is Improved on Certain 797F Off-Highway Trucks {5056}
797F Tier 4 Off-Highway Truck Engine Supplement Nitrogen Oxide Sensor (Exhaust Inlet) - Remove and Install
The Brake Cooling and Brake Charging Pump May Lose Efficiency Prematurely on Certain 777G Off-Highway Trucks {5073} The Brake Cooling and Brake Charging Pump May Lose Efficiency Prematurely on Certain 777G Off-Highway Trucks {5073}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Boom/Stick/Bucket Combinations
320D3 and 323D3 Excavators Systems Pump Control (Main Hydraulic) - Main Pump Regulator
C18 Generator set and C18 Marine Engines Fuel Manifold - Remove
320D3 Hydraulic Excavator Machine Systems Monitor - Remove and Install - Machine