1986/04/01 Caterpillar


Fuel Injection Timing Changed To 15° With New 3.5° Timing Advance

Usage:


3208 (1Z) Marine Engines Rated At 280 kW (375 hp)

Description of Change: The fuel injection static timing on 3208 TA Marine Engines rated at 280 kW (375 hp) has been changed from 18° BTC with no timing advance to 15° BTC with a 3.5° timing advance. Use of the timing advance reduces the injection pump shock loads on the timing gear teeth because some of the loads are absorbed by the timing advance.

Adaptable To: This change is effective with 3208 TA Marine Engines 1Z6151-Up if they are rated at 280 kW (375 hp). Only the 7W7500 and 7W9150 Engine Arrangements are changed. Some engines prior to 1Z6151 have the new timing and are identified by "15.0 BTC" stamped on the engine information plate.

The new timing is directly adaptable to 1Z4042-1Z6150 by installing a new injection pump camshaft and the timing advance unit (gear and weight as.). See chart.

Almost all engines with serial numbers 1Z1-1Z4041 are originally equipped with a 5° timing advance unit, and are set at 15° BTC static timing. Check the engine information plate on the engine.

Caterpillar Information System:

1986/04/01 Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control
1986/04/01 Troubleshooting Solid State Suppressors
1986/03/01 New Clip Added To Water Lines Group
1986/03/01 Stronger Oil Pan Used
1986/03/01 Improved Cylinder Head Gasket
1986/03/01 New Fuel Injector Available To Reduce Smoke At Low RPM and Loads
1986/03/01 Screens Added To Inlet Air Manifolds
1986/03/01 Engine Oil Filter Element Has Metal Wrapper Instead Of Paper Wrapper
1986/03/01 High Silicates In Antifreeze
1986/03/01 Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01 New 8T2998 Lubricant Available
1986/03/01 Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers
1986/04/01 Adjust Bridge Whenever Valve Clearance Adjustments Are Made
1986/04/01 Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle
1986/04/01 New Bracket Used In Air Compressor Lines Group
1986/04/01 New Index Lists Engine Special Instructions By SMCS Code
1986/04/01 Remanufactured Short Block Available For 3204 Industrial Engines
1986/05/01 New Alternators Are Self-Energizing And Have Built-In Regulators
1986/05/01 Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct
1986/05/01 Cylinder Liner Seat Insert Available
1986/05/01 New Wire Assemblies And Spark Plug Insulators Improve Service Life Of Ignition System
1986/05/01 Silicone Rubber Hoses Available For Engine Oil Cooler Water Lines
1986/05/01 Three Element Speed Switch Replaces Dual Element Speed Switch
1986/05/01 New Conversion Groups Available To Convert From Hydramechanical Governors To Woodward PSG Governors
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.