Hydraulic Cylinder (Elevation) - Assemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 5P-3520 | Wrench Gp | 1 |
5P-8675 | Handle-Extension | 1 |
- Install O-ring seal (21) and install O-ring seal (22).
Show/hide table
Illustration 2 g06268166 - Install receptacle (20) and install four bolts (19).
Show/hide table
Illustration 3 g06268164 - Install sensor assembly (18). Connect harness assembly (17) to block (16) and install block (16).
Show/hide table
Illustration 4 g06268159 - Install bolts (15) to secure block (16). Connect harness assembly (14).
Show/hide table
Illustration 5 g06268156 - Install seal (8), seal (9), seal (10), seal (11), seal (12), and seal (13) onto cap (1).
- Install seal (4) and magnet ring (5) onto rod (3). Install piston (6) onto rod (3). Install seal (7) onto piston (6).
Show/hide table
Illustration 6 g06267033 - Install rod assembly (3) into cylinder (2).
- Use Tooling (A) to install cap (1) onto cylinder (2).
Show/hide table
Illustration 1 | g06268168 |
End By:
- Install the hydraulic cylinder (elevation).
Caterpillar Information System:
PM820, PM822, and PM825 Cold Planer Machine Systems Hydraulic Cylinder (Elevation) - Disassemble
Procedure to Install and Operate Diesel Exhaust Fluid Transfer Pump on Certain Cat® Engines {108H, 108J, 108K} Procedure to Install and Operate Diesel Exhaust Fluid Transfer Pump on Certain Cat® Engines {108H, 108J, 108K}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Window (Front)
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Stopping the Engine
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Engine and Machine Warm-Up
3500 Engines Fuel Control Actuator - Remove and Install - Dynamic Gas Blending
New Heat Shield Plates for the Exhaust Thermocouples Are Now Used for Certain 3512 and 3516 Marine Engines {1073} New Heat Shield Plates for the Exhaust Thermocouples Are Now Used for Certain 3512 and 3516 Marine Engines {1073}
3500 Engines Gas Shutoff Valve - Remove and Install - Dynamic Gas Blending
336 and 336 GC Excavator Daily Inspection
3500 Engines Gas Pressure Regulator - Remove and Install - Dynamic Gas Blending
EMCP Battery Charger Set Point Updates for Certain Cat® Engines {4490, 751B} EMCP Battery Charger Set Point Updates for Certain Cat® Engines {4490, 751B}
320D3 and 323D3 Excavators Systems Oil Makeup (Travel System)
C9.3B Engine Event Codes
3412C Generator Sets Product Description
G3516 TA Engine Exhaust Manifold
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Storage and Literature Compartment
New Monitor Software is Now Available for Certain Cat® Products {1901, 7490, 7610, 7620} New Monitor Software is Now Available for Certain Cat® Products {1901, 7490, 7610, 7620}
C11 and C13 Engines Engine Oil Filter
3412C Generator Sets Generator Lead Connections
3412C Generator Set Generator Operation
C11 and C13 Engines Turbocharger
C7.1 Marine Propulsion Engine Fuel Injection Pump - Remove and Install
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Work Tool Control
A New Limit Switch is Now Available for Certain C280 Engines {1408, 1435} A New Limit Switch is Now Available for Certain C280 Engines {1408, 1435}