Hydraulic Cylinder (Elevation) - Disassemble
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 5P-3520 | Wrench Gp | 1 |
| 5P-8675 | Handle-Extension | 1 | |
Start By:
- Remove the hydraulic cylinder (elevation).
- Use Tooling (A) to remove cap (1) from cylinder (2).
- Remove rod assembly (3) from cylinder (2).
Show/hide table
Illustration 2 g06268156 - Remove seal (7) from piston (6). Remove piston (6) from rod (3). Remove seal (4) and magnet ring (5) from rod (3).
- Remove seal (8), seal (9), seal (10), seal (11), seal (12), and seal (13) from cap (1).
Show/hide table
Illustration 3 g06268159 - Disconnect harness assembly (14).
- Remove bolts (15) and detach block (16).
Note: Remove block carefully as the block will remain attached by a harness assembly.
Show/hide table
Illustration 4 g06268164 - Disconnect harness assembly (17) from block (16) and remove block (16). Remove sensor assembly (18).
Show/hide table
Illustration 5 g06268166 - Remove four bolts (19) and remove receptacle (20).
Show/hide table
Illustration 6 g06268168 - Remove O-ring seal (21) and remove O-ring seal (22).
Show/hide table
| |
| Illustration 1 | g06267033 |
Caterpillar Information System:
Procedure to Install and Operate Diesel Exhaust Fluid Transfer Pump on Certain Cat® Engines {108H, 108J, 108K} Procedure to Install and Operate Diesel Exhaust Fluid Transfer Pump on Certain Cat® Engines {108H, 108J, 108K}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Window (Front)
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Stopping the Engine
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Engine and Machine Warm-Up
3500 Engines Fuel Control Actuator - Remove and Install - Dynamic Gas Blending
New Heat Shield Plates for the Exhaust Thermocouples Are Now Used for Certain 3512 and 3516 Marine Engines {1073} New Heat Shield Plates for the Exhaust Thermocouples Are Now Used for Certain 3512 and 3516 Marine Engines {1073}
3500 Engines Gas Shutoff Valve - Remove and Install - Dynamic Gas Blending
336 and 336 GC Excavator Daily Inspection
3500 Engines Gas Pressure Regulator - Remove and Install - Dynamic Gas Blending
EMCP Battery Charger Set Point Updates for Certain Cat® Engines {4490, 751B} EMCP Battery Charger Set Point Updates for Certain Cat® Engines {4490, 751B}
320D3 and 323D3 Excavators Systems Oil Makeup (Travel System)
New Aftercooler Heat Shield Group is Now Used on Certain 3516 Engines {1063} New Aftercooler Heat Shield Group is Now Used on Certain 3516 Engines {1063}
PM820, PM822, and PM825 Cold Planer Machine Systems Hydraulic Cylinder (Elevation) - Assemble
C9.3B Engine Event Codes
3412C Generator Sets Product Description
G3516 TA Engine Exhaust Manifold
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Storage and Literature Compartment
New Monitor Software is Now Available for Certain Cat® Products {1901, 7490, 7610, 7620} New Monitor Software is Now Available for Certain Cat® Products {1901, 7490, 7610, 7620}
C11 and C13 Engines Engine Oil Filter
3412C Generator Sets Generator Lead Connections
3412C Generator Set Generator Operation
C11 and C13 Engines Turbocharger
C7.1 Marine Propulsion Engine Fuel Injection Pump - Remove and Install
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Work Tool Control