Solenoid Valves
Show/hide table
图 1 | g06213809 |
位于泵室中的附件阀(A1 和 A2)(典型示例) |
Show/hide table
图 2 | g06191521 |
阀剖面、液压示意图符号和电气接头名称 |
注: 表 1 中的值仅用于台架测试。 数值可能不代表机器系统技术规格参数。
Show/hide table
额定电压 | 12 VDC |
线圈电阻 | 8.15 ± 0.4Ω (T=20° C) |
Show/hide table
图 3 | g06237029 |
A - 端口压力 (kPa) vs 电流 (mA) |
比例减压阀通过电子方式控制附件控制阀的滑阀移动压力。 这些阀通过电子控制输入或液压控制输入来控制附件控制阀。 由于动力换档压力是根据操作员控制输入进行控制,因此作业机具的操作得当增强。
Show/hide table
图 4 | g06213876 |
位于回转马达室中的附件阀 (A3)(典型示例) |
Show/hide table
图 5 | g02304193 |
阀剖面、液压示意图符号和电气接头名称 |
注: 表 2 中的值仅用于台架测试。 数值可能不代表机器系统技术规格参数。
Show/hide table
电流范围 | 0 mA ~ 700 mA |
线圈电阻 | 15.0 ± 0.5Ω (T=20° C) |
Show/hide table
图 6 | g02263554 |
A - 端口压力 (kPa) vs 电流 (mA) |
比例减压阀通过电子方式控制附件控制阀的滑阀移动压力。 这些阀通过电子控制输入或液压控制输入来控制附件控制阀。 由于动力换档压力是根据操作员控制输入进行控制,因此作业机具的操作得当增强。
Show/hide table
图 7 | g06213779 |
可变安全阀位于回转马达室上方(典型示例) |
Show/hide table
图 8 | g02304476 |
电磁阀、液压示意图符号和电气接头名称 |
注: 表 3 中的值仅用于台架测试。 数值可能不代表机器系统技术规格参数。
Show/hide table
最大流速 | 400 L/min |
P-端口压力范围 | 980 kPa 至 37700 kPa |
电流范围 | 0 mA ~ 1500 mA |
线圈电阻 | 6.4 Ω (T=20° C) |
Show/hide table
图 9 | g03354830 |
P - 端口压力 (kPa) 与 电流 (mA) |
可调安全阀比例电磁阀由机器 ECM 直接控制。 当 ECM 确定作业机具的安全压力要求时,ECM 向电磁阀发送不同信号。 其中两个电磁阀用于控制单向流和双向流作业机具释放压力。 过多的机油输送至单向液流回油系统。
Caterpillar Information System:
320 GC, 320 and 323 Excavators Tool Control System Sensors
320 GC, 320 and 323 Excavators Tool Control System Switches
320 GC, 320 and 323 Excavators Tool Control System Work Tool Parameters - Control Functions
320 GC, 320 and 323 Excavators Tool Control System Medium Pressure Hydraulic System
G3516 Petroleum Engines Exhaust Manifold - Install
320 GC, 320 and 323 Excavators Tool Control System Combined Function - Manual Relief
320 GC, 320 and 323 Excavators Tool Control System Combined Function - Electric Relief
320 GC, 320 and 323 Excavators Tool Control System General Information
3512E Tier 4 Final Engines for Land Electric Drilling Prelubrication Pump Problem
Base Mounted Recirculating Parts Washers {0374, 0599, 0680, 0699, 0700} Base Mounted Recirculating Parts Washers {0374, 0599, 0680, 0699, 0700}
3512E Tier 4 Final Engines for Land Electric Drilling Solenoid Valve - Test
C9.3B Engines for Caterpillar Built Machines Cylinder Liner - Remove
320 GC, 320 and 323 Excavators Tool Control System System Identification
320 GC, 320 and 323 Excavators Tool Control System Process for Setting Up the Work Tool
320 GC, 320 and 323 Excavators Tool Control System Work Tool Parameter - Program
320 GC, 320 and 323 Excavators Tool Control System Work Tool - Select
330, 330 GC, 336, 336 GC and 340 Excavator Tool Control Solenoid Valve (Proportional Reducing) - Calibrate - Variable Relief Valves
320 GC, 320 and 323 Excavators Tool Control System Combined Function - Electric Relief - Default Value of Work Tool Parameters
Electric Starting Motor on Certain C7.1 Engines {1453} Electric Starting Motor on Certain C7.1 Engines {1453}
320 GC, 320 and 323 Excavator Machine Systems Implement - Calibrate
Caterpillar Retail Gaseous Fueled Generator Set In-phase Synchronization Configuration {0734, 1021, 1920} Caterpillar Retail Gaseous Fueled Generator Set In-phase Synchronization Configuration {0734, 1021, 1920}
C9.3B Engines for Caterpillar Built Machines Cylinder Liner - Install
XQP1100 Generator Set Model View Illustrations
320 GC, 320 and 323 Excavators Tool Control System Combined Function - Electric Relief - Parameter Setting