Maintenance Interval Schedule - Standby
Ensure that all safety information, warnings, and instructions are read and understood before any operation or any maintenance procedures are performed. The user is responsible for the performance of maintenance, including all adjustments, the use of proper lubricants, fluids, and filters. The user is also responsible for the replacement of components due to normal wear and aging. Failure to adhere to proper maintenance intervals and procedures may result in diminished performance of the product and/or accelerated wear of components. Use fuel consumption, service hours, or calendar time, WHICH EVER OCCURS FIRST, to determine the maintenance intervals. Products that operate in severe operating conditions may require more frequent maintenance. Before each consecutive interval is performed, all maintenance from the previous interval must be performed.
Battery or Battery Cable - Disconnect
Fuel System - Prime
Generator - Dry
Generator Bearing Temperature - Test/Record
Generator Load - Check
Generator Set - Test
Generator Set Alignment - Check
Rotating Rectifier - Check
Rotating Rectifier - Inspect/Test
Electrical Connections - Check
Engine Oil Level - Check
Fuel System Primary Filter/Water Separator - Drain
Fuel Tank Water and Sediment - Drain
Generator - Inspect
Hoses and Clamps - Inspect/Replace
Walk-Around Inspection
Belts - Inspect/Adjust/Replace
Coolant Sample (Level 2) - Obtain
Engine - Clean
Engine Mounts - Inspect
Engine Oil Sample - Obtain
Engine Oil and Filter - Change
Fuel System Primary Filter (Water Separator) Element - Replace
Fuel System Secondary Filter - Replace
Generator Set Vibration - Test/Record
Rotating Rectifier - Check
Starting Motor - Inspect
Water Pump - Inspect
Coolant Extender (ELC) - Add
Coolant Temperature Regulator - Replace
When Required
Battery - RecycleBattery or Battery Cable - Disconnect
Fuel System - Prime
Generator - Dry
Generator Bearing Temperature - Test/Record
Generator Load - Check
Generator Set - Test
Generator Set Alignment - Check
Rotating Rectifier - Check
Rotating Rectifier - Inspect/Test
Every Week
Battery Electrolyte Level - CheckElectrical Connections - Check
Engine Oil Level - Check
Fuel System Primary Filter/Water Separator - Drain
Fuel Tank Water and Sediment - Drain
Generator - Inspect
Hoses and Clamps - Inspect/Replace
Walk-Around Inspection
Every Year
Alternator - InspectBelts - Inspect/Adjust/Replace
Coolant Sample (Level 2) - Obtain
Engine - Clean
Engine Mounts - Inspect
Engine Oil Sample - Obtain
Engine Oil and Filter - Change
Fuel System Primary Filter (Water Separator) Element - Replace
Fuel System Secondary Filter - Replace
Generator Set Vibration - Test/Record
Rotating Rectifier - Check
Starting Motor - Inspect
Water Pump - Inspect
Every 3 Years
Battery - ReplaceCoolant Extender (ELC) - Add
Coolant Temperature Regulator - Replace
Every 6 Years
Coolant (ELC) - ChangeCaterpillar Information System:
A New Hose is Now Available for Certain 3412 Series Engines {1074, 1317} A New Hose is Now Available for Certain 3412 Series Engines {1074, 1317}
120 and 120 AWD Motor Grader Jacking Locations
3512E Tier 4 Final Engines for Land Electric Drilling Engine Oil Cooler
3512E Tier 4 Final Engines for Land Electric Drilling Engine Oil Cooler Bypass and Cooling Jet Sequence Valves
Cat® Reman Announces Changes to the Remanufactured Injector Rocker Arms for 3406E and C15 Truck Engines {1123} Cat® Reman Announces Changes to the Remanufactured Injector Rocker Arms for 3406E and C15 Truck Engines {1123}
Cat® Reman Announces Changes to the Remanufactured Injector Rocker Arms for 3406E, 3456, C15, C16, C18, C27, and, C32 Machine Engines {1123} Cat® Reman Announces Changes to the Remanufactured Injector Rocker Arms for 3406E, 3456, C15, C16, C18, C27, and, C32 Machine Engines {1123}
Cat® Reman Announces Changes to the Remanufactured Injector Rocker Arms for 3406E, 3456, C15, C16, C18, C27, and, C32 Engines {1123} Cat® Reman Announces Changes to the Remanufactured Injector Rocker Arms for 3406E, 3456, C15, C16, C18, C27, and, C32 Engines {1123}
330 GC and 330 Excavator Diesel Exhaust Fluid Filter - Replace - C7.1 Engine
PM820, PM822, and PM825 Cold Planer Machine Systems Piston Motor (Hydraulic Fan) - Assemble
PM820, PM822, and PM825 Cold Planer Machine Systems Piston Motor (Hydraulic Fan) - Disassemble
3512E Tier 4 Final Engines for Land Electric Drilling NOx Reduction System (NRS) - Test
120 and 120 AWD Motor Grader Stopping the Machine
797 Off-Highway Truck Steering Cylinder - Remove and Install - If equipped with Special Nuts
C7.1 Generator Sets Maintenance Interval Schedule - Prime Power
A New Flow Limiter Is Now Used for Certain C175 Engines {127A, 1288} A New Flow Limiter Is Now Used for Certain C175 Engines {127A, 1288}
320 GC, 320 and 323 Excavator Oil Filter (Hydraulic Hammer) - Replace
Special Instructions Are Available for Retrofitting the Dynamic Gas Blending Kits on Certain 3512B 1000 RPM Engines {1250, 1280} Special Instructions Are Available for Retrofitting the Dynamic Gas Blending Kits on Certain 3512B 1000 RPM Engines {1250, 1280}
C280-16 Marine Propulsion Engine Event Codes
C280-16 Marine Propulsion Engine SCR Catalyst Temperature Sensor - Test
C280-16 Marine Propulsion Engine DEF Tank Level Is Low
C280-16 Marine Propulsion Engine Diagnostic Trouble Codes
3512E Tier 4 Final Engines for Land Electric Drilling Radiator
3512E Tier 4 Final Engines for Land Electric Drilling Gear Group (Front)
3512E Tier 4 Final Engines for Land Electric Drilling Fumes Disposal Group