Engine Oil Pan - Remove and Install
Show/hide table
| Required Tooling | |||
| Tool | Part Number | Part Description | Qty |
| A | - | Loctite 596 RTV Silicone High Temp | - |
| B | - | Loctite 290 Threadlocker - High Strength Wicking Grade | - |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Drain the engine oil. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the proper draining and filling procedures.
Show/hide table
Illustration 1 g06039698 - Remove bolts (1), bolts (3), and tube assembly (2).
Show/hide table
Illustration 2 g06039746 - Use a suitable lifting device to remove oil pan assembly (5). The weight of oil pan assembly (5) is approximately
98 kg (216 lb) . - Remove bolts (4), oil pan assembly (5), and the gasket.
- Install oil pan assembly (5) in the reverse order of removal.
- Apply Tooling (A) above and below the gasket as required prior to assembly.
- Apply Tooling (B) to the threads of bolts (4) as required.
Caterpillar Information System:
XQP150 Rental Generator Set Alternator - Inspect
XQP150 Rental Generator Set Battery - Replace
C12.9 Marine Engines Crankcase Pressure Sensor - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Radiator
C18 Generator Set Engines Diesel Particulate Filter - Remove and Install
Installation Procedure for the Aftercooler on Certain 3512C Locomotive Engines {1059, 1063, 1064} Installation Procedure for the Aftercooler on Certain 3512C Locomotive Engines {1059, 1063, 1064}
Proximity Awareness Commissioning Checklist {7605, 7610, 7620} Proximity Awareness Commissioning Checklist {7605, 7610, 7620}
Cat® Command for Hauling Terrain Onboard Commissioning Procedure {7610, 7620} Cat® Command for Hauling Terrain Onboard Commissioning Procedure {7610, 7620}
Improved Transmission Filter Bypass Switch is Now Used on Certain Products {3004, 3067} Improved Transmission Filter Bypass Switch is Now Used on Certain Products {3004, 3067}
Cat® Site Positioning Commissioning Procedure {7605, 7610, 7620} Cat® Site Positioning Commissioning Procedure {7605, 7610, 7620}
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Sensor Supply - Test
C18 Generator Set Engines Catalyst (SCR) - Remove and Install
XQP1100 Generator Set Stopping the Engine
DG30, DG50, DG60, DG80, DG100, DG125, and DG150 Generator Set Engines Closed Crankcase Ventilation (CCV) System
C18 Generator Set Engines Inlet Module (Catalyst) - Remove and Install
C18 Generator Sets Voltage Regulators
C18 Generator Set Engines Air Inlet Elbow - Remove and Install
3512E Engines Engine Oil Pan - Disassemble
C175 Generator Sets Overhaul (Top End)
C18 Generator Set Engines Inlet and Exhaust Valve Springs - Remove and Install
3512E Tier 4 Final Engines for Land Electric Drilling Fuel Injector
XQP150 Rental Generator Set Single Unit Operation
XQP150 Rental Generator Set Generator Operation
TR35 Railway Transmission Speed Sensor