Module LIN Communication Wiring (Expanded Enclosure)
The module LIN communication harness is slightly complicated to route. Care should be taken to avoid damage to the nodes of the harness when pulling through the enclosure. In general, the module LIN communication harness will follow the pattern shown in Illustration 1.
Show/hide table
| |
| Illustration 1 | g06009245 |
|
Top view of module LIN communication harness (1) Electronics bay | |
- Route from expansion enclosure to primary enclosure through the separating wall.
- Route through the cable tray to the electronics bay.
- Route through the electronics bay to the EBMS.
The following steps outline the specific instructions for wiring the LIN communication harness.
- Uncoil the module LIN communication harness (long) from the expansion enclosure.
Show/hide table
Illustration 2 g06009250 Module LIN communication harness routing - primary enclosure entry (cells 1- 9) Show/hide table
Illustration 3 g06009255 Module LIN communication harness routing - primary enclosure entry (cells 10 - 18) - Route the harness into the primary enclosure through the holes shown in Illustration 2 and Illustration 3.
- Once both sides of the module LIN communication harness are inside the primary enclosure, route the two pieces through the cable tray.
- Next, route both ends of the LIN cable into the electronics panel.
- Connect one end to J6 and one end to J8 of the EBMS for that module. Either end may be connected to either J6 or J8.
Caterpillar Information System:
DG30, DG50, DG60, DG80, DG100, DG125, and DG150 Generator Set Engines Fuel Injection Lines
Information on A/D/G Coatings for Bolts, Spacers, and Washers {7000, 7553, 7553} Information on A/D/G Coatings for Bolts, Spacers, and Washers {7000, 7553, 7553}
C18 Generator Set Engines Nozzle Heater Harness - Remove and Install
C18 Marine Generator Set Radiator - Clean
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Maintenance Interval Schedule - Standby
C12.9 Marine Propulsion Engine Cooling System
C8.7 Marine Engine Starting the Engine
New Fuel Hose Assemblies Are Now Used on Certain 3500 Engines {1252} New Fuel Hose Assemblies Are Now Used on Certain 3500 Engines {1252}
C12.9 Marine Propulsion Engine Closed Crankcase Ventilation (CCV) System
New Cylinder Head Groups Are Used For Certain 3500 Engines {1100} New Cylinder Head Groups Are Used For Certain 3500 Engines {1100}
C12.9 Marine Engines Self-Diagnostics
C4.4 Engines DEF Pressure Does Not Respond
A New Air-To-Air Aftercooler Hose Is Used on Certain C27 and C32 Engines {1071} A New Air-To-Air Aftercooler Hose Is Used on Certain C27 and C32 Engines {1071}
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Generator Bearing - Replace
C175-16 Locomotive Engines Fuel Filter Differential Pressure - Check
DG30, DG50, DG60, DG80, DG100, DG125 and DG150 Generator Sets Product Description
C175-20 Locomotive Engine Manifold DEF Temperature Is Low
HPU300 Hydraulic Power Pack Electrical System
HPU300 Hydraulic Power Pack Tire Information
HPU300 Hydraulic Power Pack Motor Stopping
New Software Is Now Available for all Cat® Object Detection and Vision Applications On Certain Cat® Products {7610, 7620} New Software Is Now Available for all Cat® Object Detection and Vision Applications On Certain Cat® Products {7610, 7620}
C1.7 and C2.2 Industrial Engine Component Location
C18 Generator Set Engines Ignition Coil - Remove and Install
DG30, DG50, DG60, DG80, DG100, DG125 and DG150 Generator Sets Product Storage