Fuel System Primary Filter/Water Separator - Drain
Show/hide table
渗漏或溅溢到热表面或电气部件上的燃油会引起失火。 为防止可能的伤害,当更换燃油滤清器或油水分离器滤芯时,要将起动开关断开。 应立即将溅溢的燃油清除干净。 |
Show/hide table
注意 |
---|
油水分离器不是一个滤清器。 油水分离器将水从燃油中分离出来。 决不允许在油水分离器中的水位过半时运转发动机。 可能导致发动机严重损坏。 |
- 打开排放口 (1)。 用适当的容器盛接放掉的油液。 正确处置放出的液体。
- 只靠手的压力关闭排放阀 (1)。
Show/hide table
图 1 | g01316965 |
典型示例 |
此外,排放燃油细滤器中的水。 请参阅本"操作和保养手册", 燃油系统细滤器/油水分离器 - 排放了解更多信息。
Show/hide table
注意 |
---|
油水分离器在发动机正常运行时处于负压状态。 确保排放口被牢固拧紧以便防止空气进入燃油系统中。 |
Caterpillar Information System:
C1.7 and C2.2 Industrial Engines Fuel System Secondary Filter/Water Separator - Drain
C1.7 and C2.2 Industrial Engine Glow Plug Starting Aid - Test
C1.7 and C2.2 Industrial Engines Severe Service Application
C1.7 and C2.2 Industrial Engine Idle Validation - Test
C1.7 and C2.2 Industrial Engines Engine Oil Pressure Switch - Test
New Oil Filters for all Cat Machines are Available {3004, 3067, 4295, 431F, 5068} New Oil Filters for all Cat Machines are Available {3004, 3067, 4295, 431F, 5068}
ESS IQ Remote Monitoring Deployment Management
Well Stimulation Pumps Pump (Power End) Lube Oil Pressure - Check
New Coolant Lines Are Now Used For Certain 797B Off-Highway Trucks {1380} New Coolant Lines Are Now Used For Certain 797B Off-Highway Trucks {1380}
C1.7 and C2.2 Industrial Engine Coolant Temperature Is High
A New Wiring Harness Is Used on Certain 3512 HD Dynamic Gas Blending Engines {1403} A New Wiring Harness Is Used on Certain 3512 HD Dynamic Gas Blending Engines {1403}
A New Filter is Available for the DEF Tank Adaptor for C7.1 Engines {108H} A New Filter is Available for the DEF Tank Adaptor for C7.1 Engines {108H}
New Aftercooler Heat Shields Are Used on Certain 3500C Marine Engines {1063} New Aftercooler Heat Shields Are Used on Certain 3500C Marine Engines {1063}
374F Excavator Machine System Pressure Sensor
C7.1 Commercial Marine Engine Lubrication System
ESS IQ Remote Monitoring Real Time Monitor and Fleet Map
ESS IQ Remote Monitoring Work Orders
C175-20 Locomotive Engine Engine Valve Lash - Adjust
C12.9 Marine Propulsion Engine General Information
C1.7 and C2.2 Industrial Engine Shutdown (Ground Level) - Test
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Speed Signal - Test
C32 Locomotive Engine Maintenance Interval Schedule
G3512 Generator Set Nitrogen Oxide Sensor - Calibrate
G3508J, G3516J, and G3520J Engines Exhaust Shield - Remove and Install