Accessory Drive (Front) - Assemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1P-0520 | Driver Group | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Align the oil hole in the bearing and the oil hole in front adapter assembly (9). Use Tooling (A) and a suitable press to install bearing (11) into front adapter assembly (9). The bore of the bearing must be
75.0 ± 0.055 mm (2.95 ± 0.0020 inch) after installation. - Install O-ring seals (12) and (13) into front adapter assembly (9).
Show/hide table
Illustration 2 g01255149 - Place clean engine oil on the bearing and install shaft (6) in front adapter assembly (9).
- Install retaining washer (10) and the bolts.
Note: Later models have two retaining washers.
Show/hide tableIllustration 3 g01255146 - Position gear (8) on shaft (6) and install bolts (7).
Show/hide table
Illustration 4 g01255143 - Align the oil hole in the bearing and the oil hole in rear adapter assembly (1). Use Tooling (A) and a suitable press to install bearing (5) into rear adapter assembly (1). The bore of the bearing must be
75.0 ± 0.055 mm (2.95 ± 0.0020 inch) after installation. - Use Tooling (A) to install seal (4) into rear adapter assembly (1). Ensure that the lip of the seal is toward the bearing.
Show/hide table
Illustration 5 g00906726 - Install O-ring seals (2) and (3) into rear adapter assembly (1). Place clean engine oil on the O-ring seals.
Show/hide table
Illustration 1 | g01255150 |
End By:
- Install the accessory drive (front).
Caterpillar Information System:
352F OEM Excavator Based Specialty Solutions Shipping the Machine
G3606 and G3608 Engines Fuel Shutoff Solenoid - Remove and Install
C3.3B and C3.8 Engines for Caterpillar Built Machines NOx Conversion Is Low
3516E Generator Set Engine Fuel Pressure
349F and 352F Excavators Selective Catalytic Reduction Warning System
3516E Generator Set Engine Electronic Control Module (ECM)
SRMP Electric Power Generation SRMP Generator Coupling - Remove and Install
794 AC Off-Highway Truck Machine Systems Steering Control Valve - Remove and Install
Improvements to the Main Hydraulic Pump are Now Used on Certain Excavators and Mobile Hydraulic Power Units {5070} Improvements to the Main Hydraulic Pump are Now Used on Certain Excavators and Mobile Hydraulic Power Units {5070}
323F SA and 323F LN Excavator and 323F LN MHPU Machine Systems Specifications Relief Valve (Pilot)
794 AC Off-Highway Truck Machine Systems Solenoid and Manifold Valve (Steering) - Remove and Install
794 AC Off-Highway Truck Machine Systems Solenoid Valve and Manifold (Blower Fan, Final Drive Lubrication, Steering) - Remove and Install
G3508J, G3516J, and G3520J Engines Gear Group (Rear) - Remove
G3508J, G3516J, and G3520J Engines Gear Group (Rear) - Install
G3508J, G3516J, and G3520J Engines Rocker Shaft and Push Rod - Remove
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Exhaust Manifold Shield - Remove and Install
G3508J, G3516J, and G3520J Engines Rocker Shaft and Push Rod - Install
G3508J, G3516J, and G3520J Engines Cylinder Head - Remove
G3508J, G3516J, and G3520J Engines Cylinder Head - Disassemble
G3508J, G3516J, and G3520J Engines Cylinder Head - Assemble
G3508J, G3516J, and G3520J Engines Cylinder Head - Install
G3508J, G3516J, and G3520J Engines Piston Cooling Jets - Remove and Install
G3508J, G3516J, and G3520J Engines Connecting Rod Bearings - Remove and Install
G3508J, G3516J, and G3520J Engines Piston and Connecting Rods - Remove