Utility Circuit Breaker Failure to Close Circuit Fault
系统运作描述:
发生以下情况时,公用电断路器无法闭合的事件代码 4012-31 将变为现行状态:
- 在请求 EMCP 闭合断路器之后,公用电断路器没有改变状态。
EMCP 已经启用了设计用于断路器的继电器或数字输出。 公用电断路器位置仍检测到公用电断路器 AUX A 的数字输入处为闭合状态。
- 查看激活和记录的诊断代码,以确定是否有可能指示那些可能导致转换故障的系统出现故障的其他诊断。
- 确认"公用电断路器最长闭合时间"事件定时器限制的 EMCP 设定点。 确保定时器设置为分配给完整系统转换的适当时间。
- 配线:检查 EMCP 继电器或数字输出之间的系统线路是否存在间歇性开路和电阻值偏高、连接松动以及对接地短路。 EMCP 继电器或数字输出设计用于至公用电断路器的公用电断路器控制。
测试步骤 1. 检查导线线束是否存在开路或对接地短路
- 从发动机上断开蓄电池电源。
- 断开 EMCP 和公用电断路器的导线线束。
- 测量指定的继电器或数字输出与公用电断路器或公用电断路器控制设备之间的配线电阻。 如果发现电阻超过 10 欧姆,则表明可能有开路或连接不良。 修理或更换配线。 如果发现电阻小于 10 欧姆,测量 EMCP 继电器或数字输出触针和公用电断路器连接点处的蓄电池电压。 如果在两个点都发现蓄电池电源,则可能是公用电断路器故障。 如果公用电断路器上不存在蓄电池电源但 EMCP 处存在蓄电池电源,修理或更换 EMCP 和断路器连接之间的接线。
结果:
- - 停止
Caterpillar Information System:
3516B Generator Set Engines with Dynamic Gas Blending Crankcase Breather
SRMP Electric Power Generation SRMP Generator Terminal Box - Remove and Install
C175-16 Locomotive Engine Data Link - Test
C175-16 Locomotive Engine Coolant Temperature Control Module - Test
C175-16 Locomotive Engine Coolant Pressure Is Low
3516E Generator Set Engine Cat ET Service Features
C1.7 and C2.2 Industrial Engine Alternator Problem
C1.7 and C2.2 Industrial Engine Diagnostic Trouble Codes
EMCP4.2B Utility Circuit Breaker Failure to Open Circuit Fault
C1.7 and C2.2 Industrial Engine Electrical Connectors
WS223, WS223 SS, WS223 XD, WS255, WS255 SS, WS255 XD, WSP223, WSP255, WSF223, WSF223 SS, WSF223 XD, WSF255, WSF255 SS and WSF255 XD Well Stimulation Pumps Seal - Remove and Install - Pony Rod Seal
WS223, WS223 SS, WS223 XD, WS255, WS255 SS, WS255 XD, WSP223, WSP255, WSF223, WSF223 SS, WSF223 XD, WSF255, WSF255 SS and WSF255 XD Well Stimulation Pumps Pinion Shaft - Remove and Install
Shutoff Valve Leaking on Engine Oil Pan on Certain C4.4 Engines{1307} Shutoff Valve Leaking on Engine Oil Pan on Certain C4.4 Engines{1307}
C1.7 and C2.2 Industrial Engine Engine Does Not Crank
EMCP4.2B General Information
EMCP4.2B Component Location
EMCP4.2B Electronic Control Module (Generator Set)
EMCP4.2B Data Link
EMCP4.2B Electronic Control Module (Engine)
EMCP4.2B MUI Engine Monitoring and Control
EMCP4.2B System Operation
EMCP4.2B Password Entry
EMCP4.2B Event Viewing
EMCP4.2B Event Resetting