Hydraulic Tank Guard - Install
Parts and Specification Information
Show/hide table
Illustration 1 | g03855939 |
Note: Verify that all parts are shipped and undamaged for preparation of assembly. Missing or damaged parts can be ordered prior to assembly to avoid delays during assembly.
Show/hide table
Item | Part Number | Part Description | Qty | Specification | Approximate Weight | |
292-5153 Hydraulic Tank Guard Gp or 272-3347 Hydraulic Tank Guard Gp | ||||||
1 | 9T-3988 | Filler | 2 | |||
2 | 3G-0361 | Gasket | 2 | |||
3 | 9J-3047 | Strainer | 2 | |||
4 | 9H-6454 | Gasket | 2 | |||
5 | 2D-4202 | Plate | 2 | |||
6 | 8T-2275 | Ball | 2 | |||
7 | 9G-9288 | Protection Cap Gp | 2 | |||
8 | 4M-0189 | O-Ring Seal | 2 | |||
9 | 8T-4121 | Hard Washer | 4 | |||
10 | 8T-4196 | Bolt | 4 |
Start By:
- Install the fuel tank guards
Note: Remove all protective shipping covers, flanges, plugs, caps, clamps, cable straps, and material. Retain the bolts, washers, clamps, flanges, and O-ring seals.
Note: Clean all mounting and contact surfaces free of wax, dirt, debris, paint, and grease. Chase all unprotected threaded holes with an appropriately sized tap.
Show/hide table
Do not attempt to assemble this machine until you read and you understand the assembly instructions. Improper assembly procedures could result in injury or death. |
- Remove eight bolts (11) and two covers (12).
Show/hide table
Illustration 3 g03855984 Show/hide tableIllustration 4 g03856067 Show/hide tableIllustration 5 g06393676 (1) 9T-3988 Filler
(2) 3G-0361 Gasket
(3) 9J-3047 Strainer
(4) 9H-6454 Gasket
(5) 2D-4202 Plate
(6) 8T-2275 Ball
(7) 9G-9288 Protection Cap Gp
(8) 4M-0189 O-Ring Seal
(9) 8T-4121 Hard Washer
(10) 8T-4196 Bolt - Install two O-ring seals (8), two fillers (1), eight hard washers (9), and eight bolts (10).
- Install one gasket (2), one strainer (3), one gasket (4), one plate (5), one ball (6), and one cover group (7). Repeat this step for the remaining filler.
Show/hide table
Illustration 2 | g03855982 |
Caterpillar Information System:
2015/06/26 New Software Is Used on Certain G3516C Engines {1901, 1920}
3516B Generator Set Engines with Dynamic Gas Blending Coolant Level Is Low
C8.7 Marine Engine Valve Mechanism Cover - Remove and Install
3512C Generator Set Engine Camshaft - Remove
C13 Tier 4 Final Commercial and Machine Engines with an E360 (3) Low Engine Oil Pressure Code{1304} C13 Tier 4 Final Commercial and Machine Engines with an E360 (3) Low Engine Oil Pressure Code{1304}
3512C Generator Set Engine Pistons and Connecting Rods - Install
C8.7 Marine Engine Rocker Arm and Shaft - Remove and Install
C8.7 Marine Engine Pistons and Connecting Rods - Disassemble
3512C Generator Set Engine Piston Cooling Jets - Remove and Install
G3600 A4 Engines Hoses and Clamps - Inspect/Replace
G3600 A4 Engines Electrohydraulic Actuator - Inspect
3516E Engines Engine Oil Sequence Valves - Remove and Install
2015/09/11 A New Water Tube Is Now Used on Certain C18 Engines {1379, 1380}
Procedure For Replacing The Engine Interface Box Harness On Certain G3500B Engines{4460, 7426} Procedure For Replacing The Engine Interface Box Harness On Certain G3500B Engines{4460, 7426}
G3606 and G3608 Engines Vibration Damper - Remove
G3600 A4 Engines General Hazard Information
C13 Generator Set Model View Illustrations
C13 Generator Set Product Description
C13 Generator Set Refill Capacities
G3600 A4 Engines Reference Information
G3606 and G3608 Engines Vibration Damper - Install
120 and 120 AWD Motor Grader Maintenance Interval Schedule
3512C Generator Set Engine Camshaft - Install
120 and 120 AWD Motor Grader Hydraulic System Oil Sample - Obtain