Engine Oil Filter Base - Remove and Install - Right-Hand Simplex
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 185-3630 | Strap Wrench As | 1 |
B | - | Loctite 263 High Strength Threadlocker | - |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Drain the engine oil and filter. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the proper draining and filling procedures.
- Drain the coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change" for the correct draining and filling procedures.
- Use Tooling (A) to remove engine oil filter (1).
Show/hide table
Illustration 2 g03832290 - Remove bolt (2), clips (3), and elbow (5). Disconnect hose assembly (4).
Show/hide table
Illustration 3 g03832305 - Remove nut (8), nut (9), nut (10), clips (6), clips (11), and bracket (7).
Show/hide table
Illustration 4 g03832320 - Remove bolts (12), studs (13), engine oil filter base (14), and the gasket.
Show/hide table
Illustration 5 g03832365 - Remove plugs (15), plugs (16), plugs (17), adapter assembly (18), and hollow stud (19).
Show/hide table
Illustration 6 g03832392 - Remove plugs (20), springs (21), and bypass valves (22).
Show/hide table
Illustration 1 | g03832276 |
- Install engine oil filter base (14) in the reverse order of removal.
- Apply Tooling (B) to the top
20.00 ± 0.80 mm (0.787 ± 0.032 inch) of hollow stud (19). Tighten hollow stud (19) to a torque of68 ± 7 N·m (50 ± 52 lb ft) .Show/hide tableIllustration 7 g03832416 - Tighten studs (13) and bolts (12) in numerical sequence shown in illustration 7 to a torque of
14 ± 3.5 N·m (124 ± 31 lb in) . Tighten studs (13) and bolts (12) to a final torque of28 ± 7 N·m (248 ± 62 lb in) . - Apply clean engine oil to the seal of engine oil filter (1).
- Apply Tooling (B) to the top
Caterpillar Information System:
G3408 and G3412 Engines Spark Plugs - Inspect/Adjust/Replace
C9.3 Marine Auxiliary and Generator Set Engine Diagnostic Trouble Codes
2015/06/12 New Exhaust Brackets Are Used on Certain G3500H Engines {1059}
2015/07/17 A New Tube Is Used for Certain 3500 Marine Engines {1354}
2015/05/15 Cylinder Head And Spacer Plate Gasket Failures On Certain Engines {1100, 1201}
2015/05/15 Cylinder Head And Spacer Plate Gasket Failures On Certain Machine Engines {1100, 1201}
2015/05/18 Cylinder Head And Spacer Plate Gasket Failures On Certain Truck Engines {1100}
C9.3 Marine Engine Exhaust Elbow - Remove and Install
C13, C15, and C18 Engines for Caterpillar Built Machines Electronic Service Tool Does Not Communicate
C9.3 Marine Engine Exhaust Elbow - Remove and Install
Caterpillar® C N Electric Motors Installation and Removal Guide. {5927} Caterpillar® C N Electric Motors Installation and Removal Guide. {5927}
C9.3 Marine Engine Exhaust Elbow - Remove and Install
2015/05/18 ECM Hotline Process Change {1000}
C9.3 Marine Auxiliary and Generator Set Engine Fuel Pressure Is High
C9.3 Marine Auxiliary and Generator Set Engine Sensor Signal (Analog, Active) - Test
C9.3 Marine Auxiliary and Generator Set Engine Coolant Temperature Is High
C9.3 Marine Auxiliary and Generator Set Engine Fuel Temperature Is High
C11, C13, C15, and C18 Industrial Engines Shutdown (Ground Level) - Test
C9.3 Marine Engine Engine Oil Filter Base - Remove and Install - Separate Circuit Keel Cooling Flange Connections - Right-Hand Simplex
Cat® Command For Hauling MID 039 - CID 0838 - FMI 02
Cat® Command For Hauling MID 039 - CID 0838 - FMI 03
C9.3 Marine Engine Engine Oil Filter Base - Remove and Install - Left-Hand Simplex
Cat® Command For Hauling MID 039 - CID 0839 - FMI 03
Cat® Command For Hauling MID 039 - CID 0840 - FMI 03