Oil Filter Differential Pressure Problem
Use this procedure in order to troubleshoot abnormal oil filter differential pressure or use this procedure if the following event code is active.
Show/hide table
Event Codes | ||
---|---|---|
J1939 Codes and Description | Conditions which Generate this Code | System Response |
99-16 Engine Oil Filter Differential Pressure : High - moderate severity (2) | The oil filter pressure is above the trip point of the oil filter clogging switch. | The code is logged. |
- Diagnostic codes and event codes
- Oil filter element
- Sensor circuit component
Note: The procedures have been listed in order of probability. Complete the procedures in the order of the listed test steps.
Show/hide table
Troubleshooting Test Step | Value | Result |
---|---|---|
1. Check for Codes A. Connect Cat® Electronic Technician (ET) to the service tool connector. Refer to Troubleshooting, "Electronic Service Tools", if necessary. B. Download the "Product Status Report" from the engine ECM before performing any troubleshooting or clearing diagnostic trouble codes. C. Determine if the diagnostic trouble code that directed to this procedure is present. D. Look for active diagnostic codes that are associated with the system for the event code that directed to this procedure. |
99-16 |
Result: An associated code is present. Repair: Troubleshoot any associated codes before continuing with this test. Result: A 99-16 code is present. Proceed to the next step. Result: No active codes STOP |
2. Replace the Oil Filters A. Restart the engine and check for an active event code for the filters that were changed. |
99-16 |
Result: After starting the engine, the 99-16 event code is no longer active for the filter that was changed. STOP Result: After starting the engine, the 99-16 event code remained active for the filters that were changed. The problem is not resolved, proceed to the next step. |
3. Inspect Sensor Circuit Component A. Inspect the suspected sensor, wiring, and connectors for damage and corrosion. Refer to Troubleshooting, "Electrical Connectors - Inspect" for information that is related to intermittent electrical problems. |
Component |
Result: A circuit component is damaged or corroded. Repair: Repair or replace the circuit component. Result: A circuit component is not damaged or corroded. Repair: Replace the sensor. |
Caterpillar Information System:
794 AC Off-Highway Truck Power Train Phase Module - Remove and Install - Chopper
G3512 Generator Set Fumes Disposal Filter Element - Inspect
C8.7 Marine Engines Flywheel Housing
G3600 A4 Engines Cooling System
C8.7 Marine Engines Engine Oil Filter Base
C8.7 Marine Engines Connecting Rod Bearing Journal
C8.7 Marine Engines Piston and Rings
C8.7 Marine Engine Expansion Tank - Remove and Install
C8.7 Marine Engines Cylinder Head Valves
C8.7 Marine Engines Main Bearing Journal
794 AC Off-Highway Truck Power Train Resistor - Remove and Install - Active Resistors - High Voltage Warning System
794 AC Off-Highway Truck Power Train Retarding Contactor - Remove and Install
2015/03/17 Procedure to Improve Reporting into VisionLink after Re-Registration of Product Link Systems PL121/321 {7606}
C8.7 and C12.9 Marine Engines Electromagnetic Clutch - Test
C8.7 and C12.9 Marine Engines ECM - Replace
794 AC Off-Highway Truck Power Train Phase Module - Remove and Install
794 AC Off-Highway Truck Power Train Interface Module - Remove and Install - Motor No. 1
794 AC Off-Highway Truck Power Train Interface Module - Remove and Install - Motor No.2
C7.1 Engines Relay - Test - ECM Power Relay
C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Install
C4.4 and C7.1 Engines Relay - Test - Start Relay
C7.1 Engines Sensor Signal (Analog, Passive) - Test
3500 Generator Sets with Dynamic Gas Blending Product Lifting
2015/06/12 A New Engine Wiring Harness Is Available for Certain Cat 3512C Engines {1000, 1408}