Engine Governing - Adjust
使用 Cat® 电子技师 (ET) 选择"调速器类型设定"配置参数。
对于发电机组应用,有两组燃油执行器的响应。 "同步模式"用于提供"在网断开"的同步发动机稳定性。 "下降工作"是为了"在网接通"的稳定性。 燃油执行器设定的调整与这两个响应有关。
为正常运行,电子液压执行器需要有正确的机油压力。 如果压力不足,发动机将不起动。 如果压力过大,会损坏液压系统。 对液压油压力进行两次调整:
- 液压管路有一个可调节液压系统压力的安全阀。 调节该安全阀,以实现起动和正常运行所需的充足压力。 如果压力过大,阀使油返回泵内。
- 液压油泵有一个安全阀,其是液压管路中安全阀的备用阀。 如果压力变得过大,泵在内部循环液压油。
Show/hide table
所需工具 | 数量 | |
---|---|---|
8T-0855 | 压力表 | 1 |
- 将螺塞 (4) 从歧管上拆下。 将 8T-0855 压力表固定到螺塞的开口处。
- 在额定转速下运行发动机。 拧松安全阀 (3) 底部的锁紧螺母 (2)。 使用通用扳手转动调整螺栓 (1),以获得
1550 ± 35 kPa (225 ± 5 psi) 的压力。注: 有时必须增大压力以避免起动过程中产生诊断代码。 这是因为由机油温度较高,需重新起动液压油粘度较低的发动机。 发生这种情况时,压力可以增加到最大值
1725 kPa (250 psi) 。 - 拧紧锁紧螺母 (2)。
- 停止发动机。
- 拆卸压力表。 将螺塞 (4) 安装到歧管上。
Show/hide table
图 1 | g03781005 |
左侧视图(直列式发动机) (1) 调整螺栓 (2) 锁紧螺母 (3) 压力安全阀 (4) 塞 |
Show/hide table
图 2 | g03781006 |
左侧视图(V 型发动机) (1) 调整螺栓 (2) 锁紧螺母 (3) 压力安全阀 (4) 塞 |
通常,液压油泵的安全阀不太可能需要调整。 如果维修泵,采用下列步骤。
- 拆下盖 (1),以接近调整螺钉 (3)(未显示)。 松开锁紧螺母 (2)。
- 完全向内转动调整螺钉 (3)。 然后,向外转动调整螺钉两圈半。
- 拧紧锁紧螺母 (2),并安装盖 (1)。
Show/hide table
图 3 | g03781008 |
(1) 盖
(2) 锁紧螺母 (3) 调整螺钉(未显示) |
Caterpillar Information System:
G3600 A4 Engines General Information (Electronic Control System)
Generators for C15/C18 Engines Mechanical Features
C3.3 Industrial Engine Engine Operation
C4.4 and C6.6 Engines Valve Lash Is Excessive
G3600 A4 Engines Ignition System
3512E Engines Air Cleaner - Remove and Install
G3600 A4 Engines BTU and Precombustion Chamber Adjustments
G3600 A4 Engines Excessive Engine Oil Consumption - Inspect
G3600 A4 Engines Measuring Engine Oil Pressure
G3600 A4 Engines Engine Speed Sensor - Adjust
3512E Engines Fuel Filter Housing - Remove and Install
C3.4B Engines for Caterpillar Built Machines Engine Oil Pressure
G3600 A4 Engines Pressure Regulating Valve
C32 Marine Engine Maintenance Interval Schedule - Engines Which Are Rated "E"
C32 Marine Engine Maintenance Interval Schedule - Engines Which Are Rated "B" and Engines Which Are Rated "C"
3600 Heavy Fuel Engines Maintenance Interval Schedule - Heavy Fuel
C3.3 Industrial Engine Reference Material
3512E Engines Inlet Air Temperature Sensor - Remove and Install
3512E Engines Engine Oil Temperature Sensor - Remove and Install
2015/01/23 New Varistor is Now Available for Certain Engines and Generator Sets {4450}
3512E Engines Temperature Sensor (Cooled Exhaust Gas) - Remove and Install
C13 Generator Set Engine Engine Oil Pressure Sensor - Remove and Install
C13 Generator Set Engine Crankcase Pressure Sensor - Remove and Install
C13 Generator Set Engine Fuel Pressure Sensor - Remove and Install