3306B-XQ200 Rental Generator Set Engine Caterpillar


Maintenance Interval Schedule - Prime

Usage:

3306B 8JJ
Ensure that all safety information, warnings, and instructions are read and understood before any operation or any maintenance procedures are performed.

An authorized operator may perform the maintenance items with daily intervals. An authorized operator may perform the maintenance items with intervals of every week. The maintenance that is recommended for all other maintenance intervals must be performed by an authorized service technician or by your Cat dealer.

The user is responsible for the performance of all maintenance which includes the following items: performing all adjustments, using proper lubricants, fluids, and filters and replacing old components with new components due to normal wear and aging .

Failure to adhere to proper maintenance intervals and procedures may result in diminished performance of the product and/or accelerated wear of components.

Before each consecutive interval is performed, all maintenance from the previous intervals must be performed.

Choose the interval that occurs first in order to determine the correct maintenance interval: fuel consumption, service hours and calendar time . Products that operate in severe operating conditions may require more frequent maintenance.

All of the following will affect the oil change interval: operating conditions, fuel type, oil type and size of the oil sump . Scheduled oil sampling analyzes used oil in order to determine if the oil change interval is suitable for your specific engine.

Refer to this Operation and Maintenance Manual, "Engine Oil and Filter - Change" in order to determine the oil change interval that is suitable for your specific engine.

To determine the maintenance intervals for the overhauls, refer to this Operation and Maintenance Manual, "Maintenance Recommendations" .

Unless other instructions are provided, perform maintenance and perform repairs under the following conditions:

The starting system is disabled.

The engine is stopped.

The generator does not pose an electrical shock hazard.

The generator is disconnected from the load.

When Required

Battery - Replace
Battery or Battery Cable - Disconnect
Enclosure - Inspect
Engine Air Cleaner Element (Dual Element) - Clean/Replace
Engine Air Cleaner Element (Single Element) - Inspect/Replace
Fuel System - Prime
Trailer - Inspect

Daily

Cooling System Coolant Level - Check
Engine Air Cleaner Service Indicator - Inspect
Engine Oil Level - Check
Fuel System Water Separator - Drain
Walk-Around Inspection

Between 250 Service Hours and 1000 Service Hours (or between first and fourth oil change)

Magnetic Pickups - Clean/Inspect

Every 1000 Service Hours

Engine - Clean

Every Year

Fuel Ratio Control - Inspect/Adjust

Every 8500 L (2200 US gal) of Fuel or 250 Service Hours

Battery Electrolyte Level - Check
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
Engine Crankcase Breather - Clean
Engine Oil Sample - Obtain
Engine Oil and Filter - Change
Fan Drive Bearing - Lubricate
Fuel System Secondary Filter - Replace
Fuel Tank Water and Sediment - Drain
Hoses and Clamps - Inspect/Replace
Radiator - Clean

Every 34 000 L (9000 US gal) of Fuel or 1000 Service Hours

Fuel Control Linkage - Check/Lubricate

Every 67 000 L (18 000 US gal) of Fuel or 2000 Service Hours

Crankshaft Vibration Damper - Inspect
Engine Mounts - Inspect
Engine Valve Lash - Inspect/Adjust
Engine Valve Rotators - Inspect
Fuel Injection Nozzles - Test/Exchange
Fuel Ratio Control - Inspect/Adjust
Turbocharger - Inspect

Every 91 000 L (24 000 US gal) of Fuel or 3000 Service Hours

Aftercooler Core - Clean/Test
Cooling System Coolant Extender (ELC) - Add
Cooling System Water Temperature Regulator - Replace
Water Pump - Inspect

Every 136 000 L (36 000 US gal) of Fuel or 4000 Service Hours

Alternator - Inspect
Starting Motor - Inspect

Every 228 000 L (60 000 US gal) of Fuel or 6000 Service Hours or 6 Years

Cooling System Coolant (DEAC) - Change
Cooling System Coolant (ELC) - Change

Overhaul

Overhaul Considerations

Caterpillar Information System:

C4.4 Marine Generator Set Fuel Filter Base - Remove and Install - Non M.C.S. Primary Fuel Filter Base
XQC1200 and XQC1600 Power Modules Cylinder Liner - Remove and Install
C4.4 Marine Generator Set Fuel Filter Base - Remove and Install - M.C.S. Duplex Primary Fuel Filter Base
3516C Marine Engines Gear Group (Rear)
460-9015 Major Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9015 Major Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
3516C Marine Engines Engine Oil Lines
2014/08/13 369-4017 Ball Bearing and Accompanying Parts Are Available as a Suitable Replacement of 124-3307 Ball Bearing and Accompanying Parts On Certain TH55-E70 Transmissions {3030}
C32 Generator Set Belts - Inspect/Adjust/Replace
C3.4B Engines Diagnostic Trouble Codes
C32 Generator Set Fuel System Primary Filter/Water Separator - Drain
3516C Marine Engines Air Cleaner
C32 Generator Set Fuel System - Prime
3306B-XQ200 Rental Generator Set Engine Maintenance Interval Schedule - Standby
C280 Marine Engines Turbocharger Turbine Temperature Is High
C280 Marine Engines Cat ET Service Features
3516B Generator Set Engines with Dynamic Gas Blending Power Is Intermittently Low or Power Cutout Is Intermittent
2015/07/23 New Copper Lead Main and Connecting Rod Bearings Are Available For All 3500 Diesel Machine Engines {1203, 1219}
460-9072 Major Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9072 Major Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
460-9230 Major Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9230 Major Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
C8.7 Marine Engines Rear Gear Group - Time
2014/11/19 New Diesel Oxidation Catalyst Available for Certain C27 Tier 4 Final Engines {1050, 108D}
3516B Generator Set Engines with Dynamic Gas Blending Engine Misfires, Runs Rough or Is Unstable
368-9910 Multi-Tool Group with the 368-9911 Burn Rate Group Accuracy Issue{0599, 0701, 0702, 0706, 1000, 7610, 7620} 368-9910 Multi-Tool Group with the 368-9911 Burn Rate Group Accuracy Issue{0599, 0701, 0702, 0706, 1000, 7610, 7620}
460-9242 Major Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9242 Major Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.