Air Inlet and Exhaust Lines
Show/hide table
Illustration 1 | g03486899 |
Rear view |
Show/hide table
Illustration 2 | g03486898 |
Bolt tightening sequence |
Show/hide table
Specification for 446-5030 Air Lines Gp | |||
Item | Qty | Part | Specification Description |
1 | 16 | 6V-3917 O-Ring Seal | Before assembly, lubricate the bore lightly with 5P-3975 Rubber Lubricant. |
2 | 4 | 3J-5389 Plug | Before assembly, apply Loctite C5A Copper Anti-Seize to the threads.
Torque to |
3 | 8 | 6V-1943 High Temperature Bolt | Before assembly, apply Loctite C5A Copper Anti-Seize to the threads and bearing surfaces.
Torque to |
3 | 10 | 6J-0934 Bolt | Use the following procedure in order to assemble the aftercooler assembly and tighten the bolts:
1. Assemble the seals to the aftercooler core. 2. Temporarily secure the bottom seal to the aftercooler with tape. Do not use an adhesive, a silicone lubricant, or any other lubricant for retention of the seal. 3. Assemble the aftercooler with seals to the inlet manifold. 4. Inspect the bottom seal in order to ensure that the seal is seating correctly in the recess. 5. Install the aftercooler cover. 6. Inspect the upper seal in order to ensure that the seal is seating correctly in the recess. 7. Install the cover bolts. Hand tighten the cover bolts. 8. Tighten the bolts in a numerical sequence that is shown in Illustration 2 to 9. Again, tighten the bolts in a numerical sequence that is shown in Illustration 2 to 10. Remove the tape. |
5 | 12 | 6V-5101 O-Ring Seal | Before assembly, lubricate the bore lightly with 5P-3975 Rubber Lubricant. |
Caterpillar Information System:
3512B and 3516B Generator Set Engines with Dynamic Gas Blending Air Inlet and Exhaust Lines
2013/11/21 New Engine Software is Now Used on Certain C32 Marine Engines {1901, 1920}
Retrofit SCR Aftertreatment Diesel Particulate Filter - Replace
Retrofit SCR Aftertreatment Catalyst (DOC) - Replace
Retrofit SCR Aftertreatment Exhaust Outlet Nitrogen Oxide Sensor - Inspect/Replace
Retrofit SCR Aftertreatment Exhaust Inlet Nitrogen Oxide Sensor - Inspect/Replace
Retrofit SCR Aftertreatment Diesel Particulate Filter - Clean/Inspect
Retrofit Diesel Particulate Filter (DPF) Systems Glossary
EMCP4.1/EMCP4.2 Integrated Voltage Regulator
Retrofit SCR Aftertreatment Catalyst (SCR) - Replace
C18 Petroleum Engine Monitoring System
C18 Petroleum Engine Gauges and Indicators
C4.4 Industrial Engine Coolant (Commercial Heavy-Duty) - Change
C4.4 and C7.1 Engines Fuel Rail Pressure Problem
C7 Petroleum Engine Product Description
C7 Petroleum Engine Refill Capacities
C7 Petroleum Engine Fluid Recommendations
XQC1600 Power Module Plate Locations and Film Locations
C7 Petroleum Engine Maintenance Interval Schedule
Retrofit SCR Aftertreatment Catalyst (SCR) - Clean/Inspect
XQC1600 Power Module Electronic Modular Control Panel 4 (EMCP 4)
XQC1200 Power Module Before Starting Engine
XQC1600 Power Module Fuel Conservation Practices
Inspection Criteria for MMUs Experiencing Load Cell - CM Errors{4480} Inspection Criteria for MMUs Experiencing Load Cell - CM Errors{4480}