Electric Starting Motor
Show/hide table
Illustration 1 | g03454196 |
Show/hide table
Specification for 207-1558 Electric Starting Motor Gp     | |||
Item     | Qty     | Part     | Specification Description     |
B     | -     | -     | Clearance between the pinion and the housing is 9.1 mm (0.36 inch).     |
1     | 1     | 6V-8188 Nut     | Battery terminal. A maximum of three cable terminals or wire terminals may be used with the battery terminal nut. A maximum of two of the cable terminals may be equal to or greater than 0 AWG.     |
Torque to 30.5 ± 3.5 N·m (270.0 ± 31.0 lb in). |
|||
2     | 2     | 6V-8188 Nut     | Ground terminal. Torque to 30.5 ± 3.5 N·m (270.0 ± 31.0 lb in).     |
3     | 1     | 6V-8378 Nut     | Ground terminal. Torque to 2.25 ± 0.25 N·m (19.91 ± 2.21 lb in).     |
4     | 1     | 6V-8378 Nut     | Switch terminal. Torque to 2.25 ± 0.25 N·m (19.91 ± 2.21 lb in).     |
5     | 1     | 6V-8188 Nut     | Motor terminal. Torque to 30.5 ± 3.5 N·m (270.0 ± 31.0 lb in).     |
6     | -     | -     | Motor frame terminal. Torque to 8 ± 3 N·m (71 ± 27 lb in).     |
-     | -     | -     | Pull-in current at 20 V and 25° C (77° F) is 57 Amp.     |
-     | -     | -     | Hold-in current at 20 V and 25° C (77° F) is 16 Amp.     |
-     | -     | -     | When the electric starting motor is viewed from the pinion end, the motor rotates in the clockwise direction.     |
-     | -     | -     | No load conditions at 25 °C (77 °F):     |
Speed is 7643 ± 1683 rpm. | |||
Current draw is 76.5 ± 14.5 Amp. | |||
Voltage is 23 VDC. |
Caterpillar Information System:
G3306B Gas Engines Wiring
794 AC Off-Highway Truck Coolant Level - Check
C7 and C9 Industrial Engines Coolant Level Is Low
C15 and C18 Engines for Caterpillar Built Machines ECM Software - Install
C13, C15, and C18 Tier 4 Final Engines Electrical Connectors - Inspect
C15 and C18 Engines for Caterpillar Built Machines Timing - Calibrate
C15 and C18 Engines for Caterpillar Built Machines Customer Passwords
374F and 390F Excavators Tool Control System Switches
2014/12/10 New Software Is Now Available for All Cat® Products With The Product Link PL421 or Product Link PL420 System {7606, 7620}
2013/10/01 Recommended Capacitor As for All UPSB 125/UPSB 130 Uninterruptible Power Supply {1562, 4480}
2013/10/21 New Product Link Software for PL300 Is Now Available for All Cat ®Products {7606, 7620}
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit Switch Circuits - Test
G3306B Gas Engines Crankshaft Wear Sleeves and Seals
G3306B Gas Engines Cylinder Liner
CG137-12 Petroleum Generator Set Engine Inlet Manifold Air Pressure Sensor
G3306B Gas Engines Temperature Sensor (Catalyst Outlet)
G3306B Gas Engines Catalytic Converter
2014/08/01 A New Oil Screen is Used on the High-Pressure Fuel Pump Adapter on C175 Engines {1151, 1162, 1206}
2013/11/08 New Oil Heater Circulation Pumps and Seal Kits Are Available for Certain 3600 and C280 Engines {1333}
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit CAN Data Link - Test
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit Sensor Signal (Analog, Passive) - Test
2013/10/28 A New Outlet Elbow Is Available for Certain Commercial Engines {1307}
2014/12/23 A New Outlet Elbow Is Used on Certain Machine Engines {1307}
PM820, PM822, and PM825 Cold Planer Rotor Bearing Oil Sample - Obtain