Pinion Shaft - Remove and Install
Removal Procedure
Show/hide table
Require Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 434-9961     | Pinion Installation Sleeve     | 1     |
B     | -     | Loctite 262     | -     |
C     | 8T-5096     | Dial Indicator Group     | 1     |
Start By:
- Remove the bull gear.
- Disconnect hose assembly (1) and remove fitting (2) .
Show/hide table
Table 2 Approximate weight of the pinion shaft     Sales Model     Approximate Weight     WS273 XD
WSP273    435 kg (959 lb)     WS305 XD
WSP305    
772 kg (1702 lb)    
Show/hide table
Illustration 1 | g03396653 |
- Use a suitable lifting device to support the pinion shaft. Refer to Table 2 for the approximate weight of the pinion shaft. Remove bolts (3) and remove bearing housing (4) .
Show/hide table
Illustration 2 | g03396654 |
- Disconnect hose assembly (5) and remove fitting (6) .
Show/hide table
Illustration 3 | g03396858 |
- Use Tooling (A) and a suitable lifting device to support the pinion shaft. Refer to Table 2 for the approximate weight of the pinion shaft. Remove bolts (7) and remove bearing housing (8) .
Show/hide table
Illustration 4 | g03529456 |
- Position pinion shaft (9) half way out of the frame assembly. Reposition the suitable lifting device to the center of pinion shaft (9) . Remove pinion shaft (9) .
Show/hide table
Illustration 5 | g03396764 |
Installation Procedure
- Install pinion shaft (9) in the reverse order of removal.
- Apply Tooling (B) to the threads of bolts (3) and (7) if nylock patch is not present.
- Tighten bolts (3) and bolts (7) to a torque of 271 N·m (200 lb ft).
- Use Tooling (C) to check total pinion travel measurement. Total pinion travel tolerances are any travel measurement greater than 4.57 mm (0.180 inch).
Show/hide tableIllustration 6 g03396757
Note: To check total pinion travel measurement. Use a dead blow hammer to hit the pinion shaft (9) towards the left side (drive side) until travel stops. Install Tooling (C) and set Tooling (C) to zero. Hit the pinion shaft (9) back towards the dial indicator until travel stops. Note the travel and record the measurement.
Caterpillar Information System:
WS273 XD, WS305 XD, WSF273 XD, WSF305 XD, WSP273 and WSP305 Well Stimulation Pumps Gear (Bull) - Remove and Install
C32 Marine Generator Set Maintenance Interval Schedule
374F Excavator System Pressure Release
C11 and C13 Engines Engine Oil Filter Base
3500 Engines Air Lines
C13 Tier 4 Final Engines Engine to Transmission Adapter
G3500 Engines Alternator Mounting
C13, C15, and C18 Tier 4 Final Engines Cylinder Block
G3516 Engines Engine Oil Pan
C9.3 Industrial Engine Flywheel Housing
C9.3 Tier 4 Final Engines Flywheel Housing
3500B Industrial Engines Air Starting Motor
C32 Marine Generator Set Fumes Disposal Filter Element - Replace
C32 Marine Generator Set Fumes Disposal Filter Service Indicator - Check
WS273 XD, WS305 XD, WSF273 XD, WSF305 XD, WSP273 and WSP305 Well Stimulation Pumps Crosshead - Remove and Install
C3.3B and C3.8 Engines for Caterpillar Built Machines Diagnostic Trouble Codes
C15 and C18 Industrial Engines Flywheel Housing
3500 Engines Duplex Engine Oil Filters
C15 and C18 Industrial Engines Flywheel Housing
3500B Generator Set Engines Radiator
C15 and C18 Tier 4 Final Engines Diesel Exhaust Fluid Tank - Flush
Retrofitting the Dynamic Gas Blending Capability for Certain 3512B Off-Highway Truck Engines {1000, 1250, 7000} Retrofitting the Dynamic Gas Blending Capability for Certain 3512B Off-Highway Truck Engines {1000, 1250, 7000}
TA2 Technical Inspection for 3516B Dynamic Gas Blending Genset Engines{1000} TA2 Technical Inspection for 3516B Dynamic Gas Blending Genset Engines{1000}
3500B Generator Set Engines Turbocharger Oil Lines