Torque Converter from Transmission, Output Transfer Gears - Separate
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 369-5916 | 吊耳组件 | 1 |
| 138-7574 | 连杆支架 | 2 | |
| 1U-9200 | 杠杆式拉拔举倾机构总成 | 1 | |
开始:
- 拆下变矩器、变速箱和输出分动器。
Show/hide table
| 注意 |
|---|
|
在检查、保养、测试、调整及维修产品时，请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前，请准备好盛接液体用的适当容器。 |
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 断开线束 (1)。 切断将线束组件 (1) 固定到变矩器 (3) 上的所有电缆扎带 (2)。
Show/hide table
图 2 g03356594 Show/hide table
图 3 g03356601 - 将工具 (A) 和适当的起吊设备连接到变矩器 (3) 上。 变矩器 (3) 的重量约为
227 kg (500 lb) 。 - 拆下螺栓 (4)。 使用工具 (A) 和适当的起吊设备拆下变矩器 (3)。
Show/hide table
| |
| 图 1 | g03356579 |
Caterpillar Information System:
349F and 352F Excavators Machine System Specifications Pilot Lines
3516B Engine for the MT4400D Off-Highway Truck Cover Group (Rear Housing)
374F Excavator Machine System Oil Filter (Hydraulic)
C3.3B Tier 4 Final Engines for Caterpillar Built Machines Fuel Injection Lines
C7.1 Marine Engine Fuel Injection Lines - Remove and Install - Double Wall Fuel Injection Lines
C7.1 Marine Engine Fuel Injection Lines - Remove and Install - Non M.C.S. Fuel Injection Lines
C18 Marine Engines Diagnostic Trouble Codes
C7.1 Marine Engine Air Starting Motor - Remove and Install
C3.3B Tier 4 Final Engines for Caterpillar Built Machines Boost Pressure Sensor
G3500H 50Hz Generator Sets Additional Messages
2013/03/29 Improved VisionLinkTM Store for Minimizing Delay in Appearance of VisionLink Store - Modules is Now Available for All Caterpillar Products {7606}
2013/03/29 Device Transfers Are Now Supported In VisionLinkTM Store {7606}
2013/03/22 Use Nickel Anti-Seize When Installing Thermocouples on Engines {7498, 7555}
349F and 352F Excavators Machine System Specifications Hoist Solenoid Valve
G3512H and G3516H Generator Set Engines Electronic Control Module (Engine) - Remove and Install
966M Tier 4 and 972M Tier 4 Wheel Loaders Power Train Torque Converter to Transmission, Output Transfer Gears - Connect
C7.1 Marine Engine Aftercooler - Remove and Install - Keel-Cooled
C7.1 Marine Engine Heat Exchanger - Remove and Install - Sea Water Cooled Engine
C9.3 Engines for Caterpillar Built Machines Relay (ARD Nozzle Heater) - Remove and Install
2013/06/13 A New Compressor Bypass Actuator is Used on Certain G3500B Engines {1803, 5510}
777F, 777G, and 785D OEM Off-Highway Truck/Tractors Water Delivery System Pressure Sensor (Motor Inlet)
C7.1 Marine Engine Heat Exchanger - Disassemble - Sea Water Cooled Engine
C9.3 Engines for Caterpillar Built Machines Nozzle Heater Harness - Remove and Install
G3512H and G3516H Generator Set Engines Turbocharger - Disassemble - Dual Turbochargers