Lifter Group - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Name | Qty |
A | 1U-7262 | Telescoping Magnet | 1 |
Start By:
- Remove the engine oil pump.
- Remove the camshaft.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- If the crankshaft is installed, rotate the crankshaft in order to gain access to appropriate lifters (1).
Show/hide table
Illustration 1 g01340518 - Use Tooling (B) to remove lifters (1).
Note: Place a temporary identification mark on each lifter to identify the correct location.
- Repeat Step 1 and Step 2 to remove the remaining lifters.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
It is strongly recommended that all lifters should be replaced when a new camshaft is installed. |
- Clean the lifters. Follow Step 1.a through Step 1.c to inspect the lifters. Replace any worn lifters or damaged lifters.
- Inspect the seat of the pushrod in the lifter for visual wear or damage.
- Inspect the shank of the lifter for wear or damage. Refer to Specifications, "Lifter Group" for more information.
- Inspect the face of the lifter that runs on the camshaft for visual wear or damage.
- If the crankshaft is installed, rotate the crankshaft to access to the cylinder block in order to install appropriate lifters (1).
- Lubricate lifters (1) with clean engine oil.
Show/hide table
Illustration 2 g01340518 - Use Tooling (B) to install lifters (1) to the cylinder block. Ensure that used lifters are installed in the correct location.
Note: The lifters should be free to rotate.
- Repeat Steps 1 and 4 to install the remaining lifters.
End By:
- Install the camshaft.
- Install the engine oil pump.
Caterpillar Information System:
C7.1 Marine Engine Bearing Clearance - Check
C7.1 Marine Engine Crankshaft Gear - Remove and Install
C7.1 Marine Engine Crankshaft Timing Ring - Remove and Install
C7.1 Marine Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in position
C7.1 Marine Engine Piston Cooling Jets - Remove and Install
C7.1 Marine Engine Engine Oil Pan Plate - Remove and Install
C7.1 Marine Engine Camshaft Bearings - Remove and Install
Loader and Excavator Bucket Base Edge Assembly Welding Requirements {0679, 6001, 6101, 6102, 6103, 6104, 6110, 6112, 6120, 6122, 6138, 6503, 6523, 6530, 6800, 6801, 6823} Loader and Excavator Bucket Base Edge Assembly Welding Requirements {0679, 6001, 6101, 6102, 6103, 6104, 6110, 6112, 6120, 6122, 6138, 6503, 6523, 6530, 6800, 6801, 6823}
C8.7 and C12.9 Marine Engines Exhaust Has Excessive White Smoke
C3.8 Engines for Caterpillar Built Machines Turbocharger - Inspect
C4.4 and C7.1 Engines Exhaust Has Excessive Black Smoke
C7.1 Industrial Engine Product Description
C7.1 Marine Engine Camshaft - Remove and Install
C7.1 Marine Engine Camshaft Gear - Remove and Install
C7.1 Marine Engine Inlet and Exhaust Valve Springs - Remove and Install
C7.1 Marine Engine Inlet and Exhaust Valves - Remove and Install
C7.1 Marine Engine Engine Oil Relief Valve - Remove and Install
C7.1 Marine Engine Air Cleaner Housing - Remove and Install
C7.1 Marine Engine Jacket Water Heater - Remove and Install
C7.1 Marine Engine Electric Starting Motor - Remove and Install
C7.1 Industrial Engine Plate Locations and Film Locations
C7.1 Marine Engine Control System - Remove and Install - M.C.S. Panel
C15 and C18 Engines Product Storage
C7.1 Industrial Engine Reference Information