Crankshaft Gear - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 8H-0663 | Bearing Puller | 1 |
5F-7345 | Screw | 1 | |
126-7183 | Crossblock | 1 | |
126-7177 | Puller Leg | 2 |
Start By:
- Remove the front housing.
- Remove the engine oil pump.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (A) to remove crankshaft gear (4) from crankshaft (2).
- If necessary, remove key (1) and remove friction shim (3) from crankshaft (2).
Note: Do not remove the key from the crankshaft unless the key is damaged.
Show/hide table
Illustration 1 | g02048917 |
Show/hide table
Illustration 2 | g02049073 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- If necessary, install a new friction shim (3) to crankshaft (2).
- If necessary, install a new key (1) to crankshaft (2).
Show/hide table
Hot parts or hot components can cause burns or personal injury. Do not allow hot parts or components to contact your skin. Use protective clothing or protective equipment to protect your skin.
- Heat crankshaft gear (4) to
150° ± 50°C (302° ± 90°F) . Align the keyway on crankshaft gear (4) with key (1) in the crankshaft. Install crankshaft gear (4) to crankshaft (2). Ensure that shoulder (5) of crankshaft gear (4) is toward the front of the engine.
Show/hide table
Illustration 3 | g02052055 |
End By:
- Install the front housing.
- Install the engine oil pump.
Caterpillar Information System:
C7.1 Marine Engine Crankshaft Timing Ring - Remove and Install
C7.1 Marine Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in position
C7.1 Marine Engine Piston Cooling Jets - Remove and Install
C7.1 Marine Engine Engine Oil Pan Plate - Remove and Install
C7.1 Marine Engine Camshaft Bearings - Remove and Install
Loader and Excavator Bucket Base Edge Assembly Welding Requirements {0679, 6001, 6101, 6102, 6103, 6104, 6110, 6112, 6120, 6122, 6138, 6503, 6523, 6530, 6800, 6801, 6823} Loader and Excavator Bucket Base Edge Assembly Welding Requirements {0679, 6001, 6101, 6102, 6103, 6104, 6110, 6112, 6120, 6122, 6138, 6503, 6523, 6530, 6800, 6801, 6823}
C8.7 and C12.9 Marine Engines Exhaust Has Excessive White Smoke
C3.8 Engines for Caterpillar Built Machines Turbocharger - Inspect
C4.4 and C7.1 Engines Exhaust Has Excessive Black Smoke
C7.1 Industrial Engine Product Description
777F, 777G, and 785D OEM Off-Highway Truck/Tractors Water Delivery System Hydraulic Tank
777F, 777G, and 785D OEM Off-Highway Truck/Tractors Water Delivery System Water Pump
C7.1 Marine Engine Bearing Clearance - Check
C7.1 Marine Engine Lifter Group - Remove and Install
C7.1 Marine Engine Camshaft - Remove and Install
C7.1 Marine Engine Camshaft Gear - Remove and Install
C7.1 Marine Engine Inlet and Exhaust Valve Springs - Remove and Install
C7.1 Marine Engine Inlet and Exhaust Valves - Remove and Install
C7.1 Marine Engine Engine Oil Relief Valve - Remove and Install
C7.1 Marine Engine Air Cleaner Housing - Remove and Install
C7.1 Marine Engine Jacket Water Heater - Remove and Install
C7.1 Marine Engine Electric Starting Motor - Remove and Install
C7.1 Industrial Engine Plate Locations and Film Locations
C7.1 Marine Engine Control System - Remove and Install - M.C.S. Panel