Bearing Clearance - Check
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 198-9142 | 塑料量规(绿色) 0.025 至 0.076 mm (0.001 至 0.003 in) |
1 |
198-9143 | 塑料量规(红色) 0.051 至 0.152 mm (0.002 至 0.006 in) |
1 | |
198-9144 | 塑料量规(蓝色) 0.102 至 0.229 mm (0.004 至 0.009 in) |
1 | |
198-9145 | 塑料量规(黄色) 0.230 至 0.510 mm (0.009 至 0.020 in) |
1 |
注: 请参阅技术规格 UENR3421 "发动机设计",了解非指定的发动机扭矩值。
注: 当发动机安装在底盘上时,可能不需要塑料量规。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: Caterpillar 不推荐检查实际的轴承间隙,尤其是在小型发动机上。 此检查可能会获得不准确的信息并损坏轴承或轴颈表面。 每个 Caterpillar 发动机轴承都要进行特殊的壁厚质量检查。
注: 测量值应在技术规格内且必须使用正确的轴承。 如果在解体期间测量了缸体和连杆的曲轴轴颈和孔,则不需要做进一步检查。 然而,如果技师仍然想要测量轴承间隙,使用工具 (A) 也是可以测量的。 如果间隙小于
Show/hide table
注意 |
---|
导线、塞尺或量缸表可能会损坏轴承面。 |
技师必须小心正确地使用工具 (A)。 必须记住以下要点:
- 确保轴承和孔的后面清洁和干燥。
- 确保轴承锁片正确就位于锁片槽内。
- 曲轴与工具 (A) 的触点上不能沾有油。
- 将工具 (A) 置于盖中的轴承顶部。
注: 不允许工具 (A) 延伸到轴承边缘外。
- 使用正确的转动扭矩技术规格安装轴承盖。 不要使用冲击扳手。 在安装盖时小心不要撞出轴承。
注: 安装工具 (A) 时不要转动曲轴。
- 小心地拆卸盖,但不要卸掉工具 (A) 。 工具 (A) 在轴承盖或曲轴轴颈上时测量工具 (A) 的宽度。 参考图 1。
Show/hide table
图 1 g01152855 典型示例 - 安装轴承盖前拆卸全部的工具 (A)。
注: 用工具 (A) 测得的读数有时不清晰。 例如,工具 (A) 的所有零件并不一样宽。 测量主要宽度确保零件符合技术规格。 有关正确的间隙,请参阅技术规格手册, "连杆轴承轴颈"和技术规格手册, "主轴承轴颈"。
Caterpillar Information System:
C3.3B Engines for Caterpillar Built Machines V-Belts - Remove and Install
C3.3B Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
C27 and C32 Tier 4 Final Marine Engines Alternator and Regulator
C4.4 and C7.1 Engines System Overview
C4.4 and C7.1 Engines Welding Precaution
2013/01/16 New Software is Used For C175-16 Petroleum Engines {1901, 1920}
C3.3B Engines for Caterpillar Built Machines Fuel Injection Pump - Remove and Install
C32 Marine Engine Configuration Parameters
Some Hydraulic Couplings are Identified with an Incorrect Part Number{5057} Some Hydraulic Couplings are Identified with an Incorrect Part Number{5057}
C32 Marine Engine Engine Air Cleaner Service Indicator - Inspect
3500C Marine Engines Engine Design
308E CR Mini Hydraulic Excavator Machine System Specifications Coupler Lines
C3.3B Engines for Caterpillar Built Machines Crankshaft and Main Bearings - Remove
C3.3B Engines for Caterpillar Built Machines Crankshaft and Main Bearings - Install
C3.3B Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove and Install
C3.3B Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove and Install
C3.3B Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
C3.3B Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
C3.3B Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
C3.3B Engines for Caterpillar Built Machines Camshaft Gear - Remove and Install
C3.3B Engines for Caterpillar Built Machines Camshaft and Valve Lifters - Remove and Install
C3.3B Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
C3.3B Engines for Caterpillar Built Machines Rocker Shaft - Assemble
C3.3B Engines for Caterpillar Built Machines Rocker Shaft and Push Rod - Remove and Install