Engine Oil Lines
Show/hide table
图 1 | g03336039 |
Show/hide table
425-3176 发动机机油管路总成 的技术规格     | |||
项目     | 数量     | 零件     | 技术规格说明     |
1     | 2     | 7N-7697 柱塞     | 冷却喷嘴顺序阀: 阀必须在压差为 130 ± 30 kPa (19 ± 4 psi) 时开始开启。 阀必须在 200 ± 30 kPa (29 ± 4 psi) 时完全开启。     |
2     | 2     | 6B-9202 弹簧     | 在试验力下的长度为 68.27 mm (2.688 in)。     |
试验力为 84.5 - 99.6 N19 (.0 - 22.4 lb)。 |
|||
试验后的自由长度为 112.72 mm (4.438 in)。 |
|||
3     | 1     | 2W-1053 塞     | 拧紧至扭矩为 100 ± 15 N·m (74 ± 11 lb ft)。     |
4     | 2     | 0S-1571 螺栓     | 按以下顺序拧紧夹紧螺栓: 1. 将卡箍组件紧固到管上。 2. 将卡箍组件拧紧到弯管上。 3. 将卡箍组件拧紧到管上。     |
5     | 2     | 0S-1594 螺栓     |
Show/hide table
图 2 | g03328981 |
A 区视图 |
Show/hide table
项目     | 数量     | 零件     | 技术规格说明     |
6     | 1     | 2W-1969 旁通阀     | 机油冷却器旁通阀必须在压差为 180 ± 20 kPa (26 ± 3 psi) 时开启。     |
7     | 1     | 2W-1635 弹簧     | 在试验力下的长度为 102.0 mm (4.02 in)。     |
试验力为 518 ± 26 N (116 ± 6 lb)。 |
|||
试验后的自由长度为 143.4 mm (5.65 in)。 |
Caterpillar Information System:
3512E Tier 4 Final Engines for Land Electric Drilling Flexible Coupling
308E2 CR and 308E2 SR Mini Hydraulic Excavators Machine System Specifications Bucket Linkage
2013/01/16 An Improved Oil Pan Isolation Seal Is Used on Certain Commercial Engines {1302, 7555}
2013/01/10 An Improved Oil Pan Isolation Seal Is Available for Certain Truck Engines {1302, 7555}
C3.3B Engines for Caterpillar Built Machines Glow Plugs - Remove and Install
428-8745 Top End Engine Overhaul Foundational Kit for 3412C and 3412 Marine Engines{1000} 428-8745 Top End Engine Overhaul Foundational Kit for 3412C and 3412 Marine Engines{1000}
3512B and 3512C Petroleum Generator Set Engines Flywheel Housing
3512B and 3512C Petroleum Generator Set Engines Cover Group (Front Housing)
3512B and 3516B Generator Set Engines with Dynamic Gas Blending Water Temperature Regulator - Aftercooler
3500 Marine Engines Crankshaft
G3516 Engines Engine Oil Filter
3512E Tier 4 Final Engines for Land Electric Drilling Extension Guard (Vibration Damper)
3512B and 3516B Generator Set Engines with Dynamic Gas Blending Prelube Pump
Application of Abrasion Resistant Material{0374, 0679, 0751, 0759, 6800} Application of Abrasion Resistant Material{0374, 0679, 0751, 0759, 6800}
3500B Locomotive Engines Engine Design
3500 Industrial Engines Engine Design
3500B Locomotive Engines Engine Design
3500C Marine Engines Engine Design
3500C Marine Engines Engine Design
C3.3B Engines for Caterpillar Built Machines Pressure Sensor (Mass Air Flow) - Remove and Install
2013/01/16 Removal of the Zinc Anode Is Recommended on Certain C32 Commercial Engines {1380, 3319}
3000 Frame SR5 Electric Power Generation General Information
3000 Frame SR5 Electric Power Generation Service Tools
C32 Auxiliary Engine Aftercooler Condensate Drain Valve - Inspect/Clean