308E2 CR and 308E2 SR Mini Hydraulic Excavators Machine System Specifications Caterpillar

Bucket Linkage

Usage:

Show/hide table




Illustration 1	g03336017

Show/hide table

Table 1
Specification for 296-9646 Bucket Linkage Gp
Item	Qty	Part	Specification Description
Coat all bores for pins with 5P-0960 Grease Cartridge.
1	2	8T-4244 Nut	Position the nut (1) to the distance 0.0 to 1.0 mm (0.00 to 0.04 inch) past the end of the bolt. For locking, tighten the nut (2) against the nut (1). Torque to 70 ± 15 N·m (52 ± 11 lb ft).
2	2	8T-4244 Nut
3	-	-	During assembly of the linkage group on machine, rotate the rod end of the bucket cylinder to position the grease fitting away from the stick.
4	4	150-5689 Shim	As required, use the shim in order to adjust the lateral clearance to a maximum of 1.0 mm (0.04 inch): Thickness is 1.0 mm (0.04 inch).
5	1	296-9480 Pin	Diameter is 49.89 ± 0.02 mm (1.964 ± 0.001 inch).
6	1	296-9479 Pin	Diameter is 54.890 ± 0.023 mm (2.1610 ± 0.0009 inch).
7	4	093-0064 Shim	As required, use the shim in order to adjust the lateral clearance to a maximum of 1.0 mm (0.04 inch): Thickness is 1.0 mm (0.04 inch).
8	2	296-9481 Pin	Diameter is 49.89 ± 0.02 mm (1.964 ± 0.001 inch).
9	4	093-1432 Lip Type Seal	Dust seal must be assembled such that lip is located to the out side of the boss and directed as shown.
10	2	218-5197 Bushing	Bore before assembly is 55.200 ± 0.025 mm (2.1732 ± 0.0010 inch). Installation depth is 5.0 ± 0.5 mm (0.20 ± 0.02 inch).
11	2	296-9578 Lip Type Seal	Dust seal must be assembled such that lip is located to the out side of the boss and directed as shown.
12	2	296-9438 Bushing	Bore before assembly is 50.200 ± 0.015 mm (1.9764 ± 0.0006 inch). Installation depth is 9.5 ± 0.8 mm (0.37 ± 0.03 inch).

Caterpillar Information System:

2013/01/16 An Improved Oil Pan Isolation Seal Is Used on Certain Commercial Engines {1302, 7555}

2013/01/10 An Improved Oil Pan Isolation Seal Is Available for Certain Truck Engines {1302, 7555}

C3.3B Engines for Caterpillar Built Machines Glow Plugs - Remove and Install

428-8745 Top End Engine Overhaul Foundational Kit for 3412C and 3412 Marine Engines{1000} 428-8745 Top End Engine Overhaul Foundational Kit for 3412C and 3412 Marine Engines{1000}

3512B and 3512C Petroleum Generator Set Engines Flywheel Housing

3512B and 3512C Petroleum Generator Set Engines Cover Group (Front Housing)

3512B and 3516B Generator Set Engines with Dynamic Gas Blending Water Temperature Regulator - Aftercooler

3500 Marine Engines Crankshaft

G3516 Engines Engine Oil Filter

3512E Tier 4 Final Engines for Land Electric Drilling Extension Guard (Vibration Damper)

C3.3B Engines for Caterpillar Built Machines Electronic Unit Injector - Remove and Install

C3.3B Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install

3512E Tier 4 Final Engines for Land Electric Drilling Flexible Coupling

3512B and 3516B Generator Set Engines with Dynamic Gas Blending Engine Oil Lines

3512B and 3516B Generator Set Engines with Dynamic Gas Blending Prelube Pump

Application of Abrasion Resistant Material{0374, 0679, 0751, 0759, 6800} Application of Abrasion Resistant Material{0374, 0679, 0751, 0759, 6800}

3500B Locomotive Engines Engine Design

3500 Industrial Engines Engine Design

3500B Locomotive Engines Engine Design

3500C Marine Engines Engine Design

3500C Marine Engines Engine Design

C3.3B Engines for Caterpillar Built Machines Pressure Sensor (Mass Air Flow) - Remove and Install

2013/01/16 Removal of the Zinc Anode Is Recommended on Certain C32 Commercial Engines {1380, 3319}

3000 Frame SR5 Electric Power Generation General Information