Engine Oil Pan - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1U-7498 | Support Stand As | 4 |
1U-7501 | Extension Tube | 4 | |
B | 138-7573 | Link Bracket | 3 |
C | 323-1146 | Engine Lifting Device | 1 |
D | 4C-9614 | Silicone Sealant | - |
- Install the oil pan gasket.
Note: Apply Tooling (D) to the puzzle joints and the T joints on the gasket. Apply between the cylinder block face, the front housing, and the rear housing.
- Attach Tooling (B) and a suitable lifting device onto engine oil pan (15). The weight of engine oil pan (15) is approximately
567 kg (1250 lb) . Position engine oil pan (15) onto platform (16). Reach through the holes in platform (16) in order to install bolts (17).Show/hide tableIllustration 2 g01559193 - Attach Tooling (C) onto the engine. The weight of the engine is approximately
10343 kg (22802 lb) . Remove the engine from Tooling (A).Show/hide tableIllustration 3 g01559173 - Lower the engine onto engine oil pan (15).
Show/hide table
Illustration 4 g01559153 - Install bolts (14) on all sides of engine oil pan (15).
Show/hide table
Illustration 5 g01214573 - Connect tube assembly (13).
Show/hide table
Illustration 6 g01559073 - Connect hose assemblies (5) and (6) onto fuel filter housing (7).
Show/hide table
Illustration 7 g01214538 - Install elbow (4) onto engine oil pump (1). Install bolts (2) and bolts (3).
- Fill the engine with oil. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change".
- Turn the fuel supply valve to the ON position.
- Turn the battery disconnect switch to the ON position.
Show/hide table
Illustration 1 | g01559213 |
Caterpillar Information System:
Alternator - Bosch K1/N1 Diode Trio - Test
3612 and 3616 Engines Fuel Injection Lines Group
Alternator - Bosch K1/N1 Regulator - Test
Alternator - Bosch K1/N1 Brush Length - Check
Alternator - Bosch K1/N1 Brush Assembly - Test
Alternator - Bosch K1/N1 Alternator
Alternator - Bosch K1/N1 Rectifier - Test
C18 Marine Engine Engine Speed/Timing Sensor - Clean/Inspect
2013/04/12 New Software Is Now Available for Cat® Product Link 522 Systems {7494, 7606, 7620}
C18 Marine Engine Belts - Inspect/Adjust/Replace
C18 Marine Engine Plate Locations and Film Locations
C18 Marine Engine Safety Messages
C18 Marine Engine Zinc Rods - Inspect/Replace
C18 Marine Engine Fumes Disposal Filter Element - Replace
C18 Marine Engines Sensor Signal (Analog, Active) - Test
C175-16 Locomotive Engine Crankcase Breather - Remove and Install
C175-16 Locomotive Engine Valve Cover - Remove and Install
2012/09/17 Procedure to Program Injector Trim Files When Injector Trim Files Are Missing in the ECM of Certain Engines {1290, 1920}
C175-16 and C175-20 Locomotive Engines Rocker Shaft and Push Rods - Remove
2013/08/06 New Injectors Are Used In Certain C7 and C9 Commercial Engines {1251, 1290}
C175-16 Locomotive Engine Rocker Shaft - Disassemble
C175-16 Locomotive Engine Rocker Shaft - Assemble
C175-16 and C175-20 Locomotive Engines Rocker Shaft and Push Rods - Install
C175-16 and C175-20 Locomotive Engines Valve Lifter - Remove