Exhaust Manifold
Show/hide table
 | |
| Illustration 1 | g03221216 |
Show/hide table
| Specification for 352-4660 Exhaust Manifold Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 120 | 7L-6443 High Temperature Bolt | Before assembly, lubricate the threads and the bearing surfaces with Loctite C5A Copper Anti-Seize. |
| 2 | 120 | 3E-6916 Full Nut | Use the following tightening procedure to tighten the full nuts: Tighten to 47 ± 5 N·m (35 ± 4 lb ft). Again, tighten to 47 ± 5 N·m (35 ± 4 lb ft). |
| 3 | 2 | 0S-0509 Bolt | Before assembly, lubricate the threads and the bearing surfaces with Loctite C5A Copper Anti-Seize. |
| 4 | 8 | 0S-1594 Bolt | Before assembly, lubricate the threads and the bearing surfaces with Loctite C5A Copper Anti-Seize. |
| 5 | 4 | 5P-2603 Taperlock Stud | Before assembly, lubricate the threads with Loctite C5A Copper Anti-Seize. |
| Torque to 35 ± 5 N·m (26 ± 4 lb ft). |
|||
| 6 | 4 | 140-3047 Bolt | Before assembly, lubricate the threads and the bearing surfaces with Loctite C5A Copper Anti-Seize. |
| 7 | 64 | 9L-7373 High Temperature Bolt | Before assembly, lubricate the threads and the bearing surfaces with Loctite C5A Copper Anti-Seize. |
| 8 | 4 | 168-3349 Pipe Plug | Before assembly, lubricate the threads with Loctite C5A Copper Anti-Seize. |
| 9 | 4 | 1W-2430 V Band Clamp | Before assembly, lubricate the threads, bearing surfaces and inside diameter of clamps with Loctite C5A Copper Anti-Seize. |
| Torque to 6.50 ± 2.00 N·m (57.53 ± 17.70 lb in). |
|||
| 10 | 2 | 9X-8874 Bolt | Before assembly, lubricate the threads and the bearing surfaces with Loctite C5A Copper Anti-Seize. |
| 11 | 4 | 3B-1915 Bolt | Before assembly, lubricate the threads and the bearing surfaces with Loctite C5A Copper Anti-Seize. |
Caterpillar Information System:
3500B and 3500C Marine Engines Air Starting Motor
G3512 Gas Engine Flywheel Housing Cover
C175-16 and C175-20 Locomotive Engines Engine Oil Pan - Disassemble
C175-16 Locomotive Engine Engine Oil Pan - Remove
C280 Marine and Petroleum Engines Speed/Timing - Test
349F and 352F Excavators Lubricant Viscosities - Fluids Recommendations
C175-16 and C175-20 Locomotive Engines Engine Oil Screen - Remove and Install
349F and 352F Excavators Diesel Particulate Filter Regeneration
C175-16 and C175-20 Locomotive Engines Engine Oil and Water Pump Drive - Install
2012/11/07 New Clips Are Used to Secure the Flywheel Housing Cover {1157, 7553}
C175-16 and C175-20 Locomotive Engines Engine Oil and Water Pump Drive - Assemble
C175-16 and C175-20 Locomotive Engines Engine Oil and Water Pump Drive - Disassemble
Alternator - Bosch K1/N1 Capacitor - Test
G3516C and G3516E Gas Engines Circuit Breakers
Alternator - Bosch K1/N1 Stator - Test
C175-16 and C175-20 Locomotive Engines Engine Oil Pan - Assemble
Alternator - Bosch K1/N1 Field Winding - Test
C18 Marine Engine Product Description
C18 Marine Engine Safety Messages
C18 Marine Engine Plate Locations and Film Locations
C18 Marine Engine Belts - Inspect/Adjust/Replace
2013/04/12 New Software Is Now Available for Cat® Product Link 522 Systems {7494, 7606, 7620}
C18 Marine Engine Engine Speed/Timing Sensor - Clean/Inspect
Alternator - Bosch K1/N1 Rectifier - Test