Exhaust Back Pressure Valve - Remove and Install
拆卸步骤
开始:
- 拆下柔性排气管。 有关正确步骤,请参阅拆解和装配, "柔性排气管 - 拆卸和安装"。
- 如有必要,从冷却系统将冷却液排入合适的容器以便保存或废弃这些冷却液。 参考操作和保养手册, "冷却系统冷却液 - 更换"以了解正确的步骤。
- 断开线束组件 (3) 和线束组件 (5) 。
Show/hide table
图 1 | g03385459 |
典型示例 |
- 将线束组件 (5) 从支架 (4) 上拆下。
- 将冷却液管组件 (1) 和 (7) 从排气背压阀 (2) 上断开。
- 松开 V 形带箍 (6) 上的六角头螺栓。 支承排气背压阀 (2) 。
- 将 V 形带箍 (6) 从排气背压阀 (2) 上拆下。
注: 如果 V 形带卡箍仍紧固在法兰上,将释放油液涂抹到 V 形带卡箍上来帮助拆卸。 使用软面锤轻敲 V 形带卡箍上的螺栓来帮助拆卸。 不要使用撬杆拆卸 V 形带卡箍。
- 将排气背压阀 (2) 从排气弯头 (8) 上拆下。
注: 涡轮增压器和背压阀之间的连接可以是弯头或直连接。
- 卸下 V 形带卡箍 (6) 。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 4C-5597     | 防粘结剂     | 1     |
- 确保所有部件清洁、无磨损或损坏。 如有必要,更换所有磨损或损坏的部件。
- 使用工具 (A) 润滑 V 形带箍 (6) 的六角头螺栓。 将 V 形带箍定位到排气弯头 (8) 上。 确保 V 形带箍朝向正确。
Show/hide table
图 2 | g03385459 |
典型示例 |
- 将排气背压阀 (2) 定位到排气弯头 (8) 上。 确保排气弯头中的定位销正确接合到排气背压阀的定位孔中。
- 将 V 形带箍 (6) 定位到排气背压阀 (2) 和排气弯头 (8) 上。
- 拧紧 V 形带箍 (6) 至扭矩为 12 N·m (106 lb in)
注: 确保 V 形带箍的六角头螺栓不接触任何其他部件。
- 将冷却液管组件 (1) 和 (7) 连接到排气背压阀 (2) 上。
- 将线束组件 (5) 的接头滑到支架 (4) 上。 将线束组件 (3) 连接到线束组件 (5) 。
- 如有必要,向冷却系统中加注冷却液。 参考操作和保养手册, "冷却系统冷却液 - 更换"以了解正确的步骤。
End By: 安装柔性排气管。 有关正确步骤,请参阅 拆解和装配, "柔性排气管 - 拆卸和安装"。
Caterpillar Information System:
C7.1 Marine Generator Set High Pressure Fuel Lines
G3516 Engines Gear Group (Front)
G3500 Engines Cylinder Head Valves
G3500 Engines Auxiliary Water Pump
2012/10/24 New Engine Software Is Now Used on Certain C27 Generator Sets {1901, 1920}
C175-16 Locomotive Engine Fuel Transfer Pump - Remove
C175-16 Locomotive Engine Fuel Priming Pump - Remove and Install
Procedure to Inspect EMCP 4.2 RS485 Remote Annunciator Interface Harness On Certain 3512 and 3516 Generator Sets{1408, 4490, 7400} Procedure to Inspect EMCP 4.2 RS485 Remote Annunciator Interface Harness On Certain 3512 and 3516 Generator Sets{1408, 4490, 7400}
185-5321 Cylinder Head Lifting Hook Assembly{0599, 0632, 0703, 1101, 6459} 185-5321 Cylinder Head Lifting Hook Assembly{0599, 0632, 0703, 1101, 6459}
C175-16 Locomotive Engine Data Link - Test
3516B Engine Fuel Manifold - Remove and Install
3516B Engine Cylinder Liner - Remove
C7.1 Marine Generator Set Model View Illustrations
C13 Tier 4 Final Engines Gear Group (Front) - Time
C32 Marine Generator Set Engine Air Cleaner Element (Single Element) - Inspect/Replace
2012/09/07 Serviceability of Connecting Rod Bearings in Type 2 C175 Engines {1219}
C7.1 Marine Generator Set Product Description
C7.1 Marine Generator Set Plate Locations and Film Locations
C13 Tier 4 Final Engines Air Inlet and Exhaust System - Inspect
C7.1 Marine Generator Set Product Lifting
C32 Auxiliary Engine Manual Stop Procedure
C32 Marine Generator Set Product Description
398-6784 Recommended J Series Two Strap Adapter Welding Sequence {0679, 6800, 6801, 6802, 6803, 6805} 398-6784 Recommended J Series Two Strap Adapter Welding Sequence {0679, 6800, 6801, 6802, 6803, 6805}
398-6786 Recommended J Series Flush Mount/Abrasion Adapter Welding Sequence {0679, 6800, 6801, 6802, 6803, 6805} 398-6786 Recommended J Series Flush Mount/Abrasion Adapter Welding Sequence {0679, 6800, 6801, 6802, 6803, 6805}