3512C and 3516C Marine Engines Caterpillar

Engine Oil Lines

Usage:

3516C HZS

Show/hide table




Illustration 1	g03011817
Front view

Show/hide table

Table 1
Specification for 242-6277 Engine Oil Lines Gp
Item	Qty	Part	Specification Description
1	1	2W-1053 Plug	Torque to 100 ± 15 N·m (74 ± 11 lb ft).
2	1	8C-3446 Fluid Sampling Valve	Torque to 11 to 13 N·m (97 to 115 lb in).
3	1	2W-1969 Bypass Valve	Valve must open with a pressure difference of 180 ± 20 kPa (26 ± 3 psi).
4	1	2W-1635 Spring	Length under test force is 102.0 mm (4.02 inch).
			Test force is 518 ± 26 N (116 ± 6 lb).
			Free length after test is 143.4 mm (5.65 inch).

Show/hide table




Illustration 2	g03011836
Right side view

Show/hide table

Table 2
Specification for 242-6277 Engine Oil Lines Gp
Item	Qty	Part	Specification Description
5	2	0S-1571 Bolt	Use the following bolt tightening sequence in order to tighten the clamp bolts: Place the clamp assembly so that the clamp assembly is snug against the tube assembly. Tighten the clamp assembly to the elbow. Tighten the clamp assembly to the tube assembly.
6	2	0S-1594 Bolt
7	6	109-2332 O-Ring Seal	Lightly, lubricate the bore with the fluid that is being sealed.
8	2	6B-9202 Spring	Length under test force is 68.3 mm (2.69 inch).
			Test force is 84.5 to 99.6 N (19.0 to 22.4 lb).
			Free length after test is 112.7 mm (4.44 inch).
9	2	7N-7697 Plunger	Valves must start to open at a pressure difference of 130 ± 30 kPa (19 ± 4 psi) .
9	2	7N-7697 Plunger	Valves must be fully open at a pressure difference of 200 ± 30 kPa (29 ± 4 psi).

Caterpillar Information System:

CX48-P2300 Petroleum Transmission Transfer Gears - Remove and Install - Upper

Remanufactured Cylinder Packs Contain Improperly Installed Piston Rings for Certain Caterpillar Products{1215, 1239} Remanufactured Cylinder Packs Contain Improperly Installed Piston Rings for Certain Caterpillar Products{1215, 1239}

C3.4B Engines for Caterpillar Built Machines Diesel Particulate Filter - Remove - Through Flow Diesel Particulate Filter

C3.4B Engines for Caterpillar Built Machines Cylinder Head - Remove

C3.4B Engines for Caterpillar Built Machines Cylinder Head - Install

2012/08/10 A New Turbocharger Housing is Used on Certain 3512B Engines {1052, 1065}

G3516C and G3516E Gas Engines Junction Box

C3.4B Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install

C3.4B Engines for Caterpillar Built Machines Water Pump - Remove

C3.4B Engines for Caterpillar Built Machines Water Pump - Install

C3.4B Engines for Caterpillar Built Machines Wastegate Solenoid - Remove and Install

C3.4B Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install

2012/05/08 Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553, 7556}

CX48-P2300 Petroleum Transmission Control Manifold - Disassemble

3500C Marine Engines Engine Oil Filter

G3516 Engines Engine Oil Pump

2012/04/30 New Software Is Now Used for Certain Tier 4 Interim Commercial Engines {1920}

2012/04/24 Turbocharger Surge on Certain G3500C and G3500E Engines that are Equipped with Dual Turbochargers {1052}

2012/04/30 Improved Fuel Injector O-Ring Seals Are Used on Certain Machine Engines {1251, 1290}

2012/04/30 Improved Fuel Injector O-Ring Seals Are Used on Certain Commercial Engines {1251, 1290}

3500C Marine Engines Engine Oil Sump Pump

3512C and 3516C Marine Engines Coolant Level Switch

3500C Marine Engines Engine Oil Sump Pump

Water Temperature Regulator on Certain C6.6 and C4.4 Engines{1355, 1380} Water Temperature Regulator on Certain C6.6 and C4.4 Engines{1355, 1380}